- All Exams Instant Download
To configure the Ethernet1/0/1 port of the switch SWA as a hybrid port, its PVID is VLAN20, and when sending VLAN20 data frames without tagging, when sending VLAN 10 data frames, then the following configuration Is the process correct (choose one or more)
To configure the Ethernet1/0/1 port of the switch SWA as a hybrid port, its PVID is VLAN20, and when sending VLAN20 data frames without tagging, when sending VLAN 10 data frames, then the following configuration Is the process correct (choose one or more)A . [SWA]vlan10 [SWA-vlan 10]quit [SWA]vlan 20 [SWA-vlan20]port...
In the switching network as shown in the figure, set VLAN10 to Isolate-user-vlan VLAN2 and VLAN3 to the Secondary VLAN of VLAN 10 on the switch SWA; create VLAN2? VLAN20 on the switch SWB, and set VLAN20 to Isolate-user-vlan, The Secondary VLA with VLAN4 being VLAN20 can be judged after setting the IP address of each device as shown in the figure
In the switching network as shown in the figure, set VLAN10 to Isolate-user-vlan VLAN2 and VLAN3 to the Secondary VLAN of VLAN 10 on the switch SWA; create VLAN2? VLAN20 on the switch SWB, and set VLAN20 to Isolate-user-vlan, The Secondary VLA with VLAN4 being VLAN20 can be judged after...
Before configuring the bpdu-tunnddotlq stp command on the port where the QinQ function of the H3C series switch is enabled, the command that must be configured on this port is
Before configuring the bpdu-tunnddotlq stp command on the port where the QinQ function of the H3C series switch is enabled, the command that must be configured on this port isA . stp disableView AnswerAnswer: A
Regarding the configuration of Isolate-user-vlan and Super VLAN, the following description is correct
Regarding the configuration of Isolate-user-vlan and Super VLAN, the following description is correctA . After the local proxy ARP function is enabled on the Isolate-user-vlan interface, the intercommunication of hosts in different Secondary VLANs can be realizedB . After enabling the local proxy ARP function on the SuperVLAN interface, the...
In the switching network as shown in the figure, VLAN10 is set as Super VLAN on the switch SWA, VLAN2 and VLAN3 are Sub VLANs of VLAN10, port Ethernet1/0/3 is Trunk port, PVID is VLAN1, allowing all VLANs to pass through; Create VLAN2~VLAN20 on SWB, port Ethernet1/0/4 as Trunk port, PVID is VLAN1, allowing all VLANs to be judged by setting the IP address of each device as shown in the figure (choose one or more)
In the switching network as shown in the figure, VLAN10 is set as Super VLAN on the switch SWA, VLAN2 and VLAN3 are Sub VLANs of VLAN10, port Ethernet1/0/3 is Trunk port, PVID is VLAN1, allowing all VLANs to pass through; Create VLAN2~VLAN20 on SWB, port Ethernet1/0/4 as Trunk port,...
The configuration command to enable the global GVRP function on H3C series switches is
The configuration command to enable the global GVRP function on H3C series switches isA . GVRPView AnswerAnswer: A
Regarding the configuration BPDU and TCM BPDU, the statements are correct
Regarding the configuration BPDU and TCM BPDU, the statements are correctA . Configure BPDUs to be sent only from the designated port, and TCNBPDUs to be sent only from the root portB . Configuration BPDUs are usually only sent periodically by the root bridge, and TCNBPDUs may be sent by...
The following technologies belong to the link backup technology in the redundant backup technology.
The following technologies belong to the link backup technology in the redundant backup technology.A . STPB . RRPPC . Smart-LinkD . Dynamic routingE . Link aggregationView AnswerAnswer: ABCE
In the switching network as shown in the figure, VLAN10 is set as Isolate-user-vlan on switch SWA, VLAN2 and VLAN3 are set as Secondary VLAN of VLAN 10; VLAN2? VLAN20 is created on switch SWB, and VLAN20 is set as Isolate-user-vlan , VLAN4 is VLAN20 Secondary VLA after setting the IP address of each device as shown in the figure, if the local proxy ARP function is enabled on both SWA and SWB, and both SWA and SWB are allowed to send ICMP packets, then on PCA Execute the command tracert 10.1.1.2, the PCA will show that it needs to go through a jump to reach the PCB (please fill in the Arabic numbers)
In the switching network as shown in the figure, VLAN10 is set as Isolate-user-vlan on switch SWA, VLAN2 and VLAN3 are set as Secondary VLAN of VLAN 10; VLAN2? VLAN20 is created on switch SWB, and VLAN20 is set as Isolate-user-vlan , VLAN4 is VLAN20 Secondary VLA after setting the...
In the network connection shown in the figure, SWA and SWB are Layer 3 switches, running STP+VRRP, and after the initial configuration is completed, SWA is the root of STP and Master of VRRP, and SWC is the Layer 2 switch connected to the access terminal , The following description about network link failure is correct
In the network connection shown in the figure, SWA and SWB are Layer 3 switches, running STP+VRRP, and after the initial configuration is completed, SWA is the root of STP and Master of VRRP, and SWC is the Layer 2 switch connected to the access terminal , The following description...
