An integrator has installed a new Synergy frame into a rack with two existing Synergy frames in a customer’s environment

HOTSPOT

An integrator has installed a new Synergy frame into a rack with two existing Synergy frames in a customer’s environment.

Click where the integrator should verify that the cabling for the management ring was completed correctly.

Answer:

Explanation:

Reference: https://support.hpe.com/hpsc/doc/public/display?docId=a00048164en_us

What are valid uses for an IPv4 address pool when configuring an HPE Synergy solution? (Choose two.)

What are valid uses for an IPv4 address pool when configuring an HPE Synergy solution? (Choose two.)
A . assignment of IP addresses for NICs in an operating system
B . assignment of IP addresses for Composer appliances
C . assignment of IP addresses for PXE booting to a deployment server
D . assignment of IP addresses for interconnect modules
E . assignment of IP addresses for iLOs

Answer: DE

Explanation:

Reference: https://techlibrary.hpe.com/docs/synergy/shared/setup_overview/index.html

Which services are provided by the vCenter Server component and should be placed in the report?

An integrator prepares deployment documents with the list of all the hardware and software components. The integrator also needs a list of all infrastructure services deployed, with the functionality described.

Which services are provided by the vCenter Server component and should be placed in the report? (Choose two.)
A . Auto Deploy
B . Single Sign-On
C . Update Manager
D . Lookup Service
E . Certificate Authority

Answer: CD

Which configuration steps must the integrator perform to provide the customer with this functionality?

An integrator is installing three Synergy frames in different locations for a customer. As part of the installation, the customer requests a single monitoring dashboard that shows the current hardware status, warranty status, and open support cases of all three frames.

Which configuration steps must the integrator perform to provide the customer with this functionality?
A . Enable Remote Support and Insight Online Integration in the Composer UI
B . Install Insight Remote Support Advanced, and integrate it with HPE Global Dashboard
C . Configure OneView with iLO Amplifier pack
D . Activate iLO Federation on all installed compute nodes

Answer: C

Which component of the HPE Synergy solution should you use to set the firmware/driver baseline and the installation method for Synergy Compute nodes?

Which component of the HPE Synergy solution should you use to set the firmware/driver baseline and the installation method for Synergy Compute nodes?
A . Composer
B . Smart Update
C . Image Streamer
D . Global Dashboard

Answer: B

Explanation:

Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c05212310

How should an integrator pair interconnect bays to set up redundant fabrics in an HPE Synergy 12000 Frame?

Refer to the exhibit.

How should an integrator pair interconnect bays to set up redundant fabrics in an HPE Synergy 12000 Frame?
A . Interconnect bays 1 and 2; bays 3 and 4; bays 5 and 6.
B . Interconnect bays 1 and 6; bays 2 and 5; bays 3 and 4.
C . Interconnect bays 1 and 4; bays 2 and 5; bays 3 and 6.
D . Interconnect bays 1 and 3; bays 2 and 4; bays 5 and 6.

Answer: C

Explanation:

Reference: https://h20195.www2.hpe.com/v2/GetPDF.aspx/c04815113.pdf

Which procedure should the integrator use to address the customer’s concern?

A customer is planning an HPE Synergy solution with 20 frames and needs to minimize the number of management ports that are required to connect the frames into the existing management network.

Which procedure should the integrator use to address the customer’s concern?
A . Connect the RJ-45 front ports of each frame to an external switch. Then, connect the uplink from the external switch into the customer’s management network.
B . Connect FLMs from all frames to two external switches for redundancy. Then, connect the two uplinks from the two switches into the customer’s management network.
C . Connect the RJ-45 front ports of each frame to two external switches for redundancy. Then, connect the uplink from the two switches into the customer’s management network.
D . Connect FLMs from all frames into a management ring. Then, connect the management ring to the customer’s management network using two uplinks.

Answer: D

What is the likely cause of this issue?

Refer to the exhibit.

An integrator needs to add an FCoE connection to the server profile, but the FCoE connection type is not available.

What is the likely cause of this issue?
A . FCoE capable interconnect modules are not installed in the Synergy frame
B . Defined FCoE network is not associated with a SAN or does not have VLAN Id defined
C . A FCoE connection is not available, as there is no LIG configured for FCoE connectivity
D . The FCoE connection has not been added as a Fibre Channel connection within a server profile

Answer: D