Network Appliance NS0-176 Cisco and NetApp FlexPod Implementation and Administration Online Training
Network Appliance NS0-176 Online Training
The questions for NS0-176 were last updated at Dec 12,2025.
- Exam Code: NS0-176
- Exam Name: Cisco and NetApp FlexPod Implementation and Administration
- Certification Provider: Network Appliance
- Latest update: Dec 12,2025
Which two are required for single-wire management for Cisco UCS C-Series? (Choose two)
- A . UCS Manager 2.1 or higher
- B . VIC 1240
- C . Redundant Nexus 2232PP FEX
- D . 10 GB LOM
- E . FI 6200 family only
- F . VIC 1225
When using Clustered Data ONTAP 8.1 and later, what is the default for new aggregates?
- A . 32-bit aggregates
- B . 64-bit aggregates
- C . 128-bit aggregates
- D . cluster aggregates
- E . traditional aggregates
- F . Vserver aggregates
Which two are two possible features of the ‘Call Home’ feature in UCS Manager?
- A . Generates a text message to configured cell phone numbers
- B . Generates a syslog event
- C . Ability to proactively open a case with the Cisco TAC with the ‘Smart Call Home’ feature
- D . Generates emails to predefined email addresses when a problem is detected
- E . Allows UCS to proactively pull down new software updates from Cisco
You installed a new NetApp cluster running clustered Data ONTAP. There is a single Storage Virtual Machine (SVM) named esx1 on the cluster.
A volume named esx_datastore1 is created in the SVM esx1. The name of the root volume for the esx1 SVM is esx1_rootvol. The default export policy was applied to the volume esx1_rootvol.
You verified that the export policy applied to esx_datastore1 contains a single rule that allows all clients to mount the volume as read/write using any version of NFS. A Linux client attempts to NFS mount the volume and receives a Permission Denied error.
In this scenario, what caused this error?
- A . NFS has not been configured on the SVM esx1.
- B . The volume esx_datastore1 has not been mounted into the namespace of the esx1 SVM.
- C . UNIX permissions for the volume esx1_rootvol are not set to read/write.
- D . The default export-policy does not have at least one rule to allow all clients read-only access.
You are attempting to establish a cluster peer relationship between two NetApp clusters, but the peering process fails.
What is a cause for this failure?
- A . The intercluster LIF on each node cannot communicate with the intercluster LIF on each node in the peer cluster.
- B . The cluster LIFs on each node cannot communicate with the cluster LIFs on each node in the peer cluster.
- C . The node management LIF on each node cannot communicate with the node management LIF on each node in the peer cluster.
- D . The cluster management LIF for the cluster cannot communicate with the cluster management LIF for the peer cluster.
Given the following switch output, where would you expect see notification level messages?
N5K-1# show logging info.
Logging console: enabled (Severity: error)
Logging monitor: enabled (Severity: informational)
Logging linecard: enabled (Severity: emergency)
Logging fex: enabled (Severity: notifications)
Logging time stamp: seconds
Logging server: disabled
Logging logfile: enabled
- A . On the console
- B . On the terminal sessions
- C . On the linecard
- D . Notification messages will not be seen anywhere
Which type of pools do you need to create vHBA templates?
- A . MAC
- B . WWNN
- C . IQN
- D . WWPN
Click the Exhibit button.
On your NetApp storage system, you create a volume named datastore1, mount it to a junction path, and then set the correct export policy. When you attempt to mount the volume from VMware ESXi as a datastore, the server is unable to mount the path /datastore1. You verify that your existing NFS datastore (/datastore0) on the same NetApp storage system SVMis functioning normally.
Referring to the exhibit, what is preventing the server from mounting the new datastore?
- A . The volume is too large to be mounted as an NFS datastore
- B . The load-sharing mirrors need to be updated.
- C . Two volumes cannot be mounted using the same LIF IP address.
- D . The LIF needs to be at its home-port when the volume is mounted.
The storage administrator created an export policy for a volume on a NetApp cluster.
The export policy contains a single export rule with the parameters shown below.
– protocol nfs C rorule any
– clientmatch 10.1.16.0/255.255.255.0 – rwrule any
Two hosts attempt to access the volume using the NFS protocol shown below.
– HostA with IP address 10.1.17.37 sends an access request using the NFSv3 protocol
– HostB with IP address 10.1.16.24 sends an access request using the NFSv4 protocol
Which statement about this scenario is true?
- A . HostA’s access to the volume will be blocked by the protocol parameter;
HostB will be granted RO/RW access to the volume. - B . HostA’s access to the volume will be blocked by the clientmatch parameter;
HostB’s access to the volume will be blocked by the protocol parameter. - C . HostA will be granted RO/RW access to the volume;
HostB’s access to the volume will be blocked by the protocol parameter. - D . HostA’s access to the volume will be blocked by the clientmatch parameter;
HostB will be granted RO/RW access to the volume.
Which service may be used to manage users and groups in a vSphere environment?
- A . Microsoft Active Directory (AD)
- B . Network Time Protocol (NTP)
- C . VMware vSphere Storage APIs for Array Integration (VAAI)
- D . Domain Name System (DNS)
Latest NS0-176 Dumps Valid Version with 145 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
