Cisco 300-360 Designing Cisco Wireless Enterprise Networks Online Training
Cisco 300-360 Online Training
The questions for 300-360 were last updated at Sep 09,2025.
- Exam Code: 300-360
- Exam Name: Designing Cisco Wireless Enterprise Networks
- Certification Provider: Cisco
- Latest update: Sep 09,2025
A network engineer is preparing for an office site survey with a height of 2.5 meters.
Which three components are recommended to complete the survey? (Choose three.)
- A . Use APs with external antennas.
- B . Use DoS attack on APs while measuring the throughput.
- C . Use APs with built-in antennas.
- D . Use a battery pack to power APs.
- E . Use a drawing of the office space to draw AP and client placements.
- F . Use APs with directional antennas.
A customer is deploying a Greenfield 802.11ac network on a floor that will support approximately 300 wireless devices.
Which setting needs to be changed on Prime Infrastructure Planning Tool in order to predict the amount of access points the customer needs to service the new floor?
- A . Data Coverage Support Margin
- B . Demand Settings
- C . Add AP Field
- D . 802.11n Protocol Support
Which two best practices should be considered when a customer wants to purchase and implement Voice over Wireless for Cisco 7925 IP Phones? (Choose two.)
- A . Enable lower data rates for 2.4-GHz data WLAN and higher data rates for phones.
- B . Use a separate Cisco Wireless Lan Controller.
- C . Enable 802.1x and Cisco Centralized Key Management for phone authentication.
- D . Use dedicated Access Points only for Voice over Wireless.
- E . Set data for 2.4 GHz and voice for 5 GHz using separate SSIDs.
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)
- A . Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller is installed.
- B . Consult with the customer to ensure that the IT staff has a complete set of design and installation documents.
- C . Make sure the customer is aware that they should consider purchasing a support contract immediately after the installation is complete.
- D . Spend time with the customer to show them the controller GUI and inform them how they can reach the Cisco TAC if they have any problems.
- E . Test all the customer’s wireless devices and applications to ensure they are working properly.
Cisco 7925G phones are experiencing intermittent connectivity issues. The wireless survey reveals that the facility has no current coverage holes. The radios on the 2.4GHz channel have all been statically set to power level 1.
Which two reasons could explain why the phones are having issues on this wireless network? (Choose two.)
- A . The phones are experiencing excessive co-channel interference.
- B . The phones only operate on the 2.4 GHz band when the power level is above 25 mW.
- C . The phones are not transmitting at the same power levels as the access points.
- D . The phones are experiencing delays of less than 30 ms within their coverage cell.
- E . The phones are receiving greater than -67 dBm RSSI on the 2.4 GHz band.
An engineer must perform a survey where the target client devices range from standard Wi-Fi-equipped laptops, consumer handhelds and tablets, and low power tracking tags limited to 12 mW Tx power. With which setting should the survey AP be configured?
- A . local power 11
- B . local power 5
- C . local power 14
- D . local power 8
Which two factors influence the density of APs in a data-only WLAN environment? (Choose two.)
- A . the number of clients that will roam through the facility
- B . the type of controller chosen
- C . the defined coverage area and customer needs
- D . the number of APs dedicated to voice services
- E . channel reuse and WLAN bandwidth
An engineer is preparing for an outdoor wireless survey to mesh connect a distant remote building to a connected building.
Which two types of antennas are appropriate for this application? (Choose two.)
- A . circular polarized
- B . patch
- C . dish
- D . Yagi
- E . omni
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services.
Which of the following is a requirement for the design?
- A . overlapping -72 dBm coverage from two access points
- B . overlapping -67 dBm coverage from two access points
- C . continuous -67 dBm coverage from one access point
- D . continuous -72 dBm coverage from one access point
A cabling contractor is working at a customer facility. The contractor is asking what rating of cable should be installed in return-air areas.
Which information can be referenced to provide the contractor the requested information?
- A . OSHA Codes
- B . BICSI TDDM
- C . NEC Ratings
- D . IEEE Standards
Latest 300-360 Dumps Valid Version with 221 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
