Which of the following are true about the NE ID of an ASON NE?

Which of the following are true about the NE ID of an ASON NE?A . Each NE ID must be unique in an ASON domain.B . The NE ID and IP address of an NE must be in different network segments.C . NE IDs must be set before the ASON...

January 30, 2019 No Comments READ MORE +

When preparing for engineering information, you need to check networking information, such as the network diagram, network protection type, NE IP addresses, NE IDs, NE name allocation table, board information, fiber and cable connections, service routes and timeslot allocation, clock tracing diagram, and orderwire diagram.

When preparing for engineering information, you need to check networking information, such as the network diagram, network protection type, NE IP addresses, NE IDs, NE name allocation table, board information, fiber and cable connections, service routes and timeslot allocation, clock tracing diagram, and orderwire diagram.A . TRUEB . FALSEView AnswerAnswer:...

January 12, 2019 No Comments READ MORE +

On a network where MSP rings and SNCP rings share fiber resources, if Assigned by VC~4 is selected, you need to set holdoff time for SNCP services.

On a network where MSP rings and SNCP rings share fiber resources, if Assigned by VC~4 is selected, you need to set holdoff time for SNCP services.A . TRUEB . FALSEView AnswerAnswer: B

January 10, 2019 No Comments READ MORE +

Which of the following about the SSM protocol are true?

Which of the following about the SSM protocol are true?A . After the SSM protocol is disabled, the clock network can be unidirectional but cannot adopt a ring topology.B . After the standard SSM protocol is enabled, the clock network can be bidirectional but cannot adopt a ring topology.C ....

January 4, 2019 No Comments READ MORE +

Latency of store-and-forward equipment is the difference between the time the first bit of a data frame enters the equipment and the time the first bit exits the equipment.

Latency of store-and-forward equipment is the difference between the time the first bit of a data frame enters the equipment and the time the first bit exits the equipment.A . TRUEB . FALSEView AnswerAnswer: B

December 2, 2018 No Comments READ MORE +

Which of the following bytes cannot be processed in pass-through mode on an ADM site using OptiX NG-SDH equipment?

Which of the following bytes cannot be processed in pass-through mode on an ADM site using OptiX NG-SDH equipment?A . K1B . K2C . A1D . A2View AnswerAnswer: CD

November 23, 2018 No Comments READ MORE +

What are the characteristics of a trail?

What are the characteristics of a trail?A . A trail is a end-to-end connection.B . A trail has a source and a sink.C . A trail may pass through many intermediate nodes.D . A trail must be bidirectional.View AnswerAnswer: ABC

November 15, 2018 No Comments READ MORE +

What is the length of a standard Ethernet frame?

You need to specify the length of data frames before using a data analyzer to test throughput. What is the length of a standard Ethernet frame?A . 64 bytesB . 128 bytesC . 1518 bytesD . 1544 bytesView AnswerAnswer: ABC

October 27, 2018 No Comments READ MORE +

According to the extended SSM protocol, clock switching is performed firstly according to clock priorities, and secondly according to clock quality levels.

According to the extended SSM protocol, clock switching is performed firstly according to clock priorities, and secondly according to clock quality levels.A . TRUEB . FALSEView AnswerAnswer: B

October 18, 2018 No Comments READ MORE +

Which of the following statements is true about inter-ring service configuration?

Two SNCP rings are intersected. Which of the following statements is true about inter-ring service configuration?A . Configure one unidirectional SNCP service pair on each intersecting node.B . Configure two unidirectional SNCP service pairs on each intersecting node.C . Configure four unidirectional SNCP service pairs on each intersecting node.D ....

October 14, 2018 No Comments READ MORE +