DES-5221 Online Training Archives

If you are want to pass your DES-5221 exam, DELL EMC is the right platform where you can get DELL EMC DES-5221 exam new questions with accurate answers. DELL EMC offer you latest and relevant DELL EMC DES-5221 Specialist – Implementation Engineer, Data Center Networking Online Training that assist you to get ready and pass EMC Specialist DES-5221 in an initial try.You will clear DES-5221 Specialist – Implementation Engineer, Data Center Networking exam in just first attempt by getting DELL EMC DES-5221 Specialist – Implementation Engineer, Data Center Networking Online Training from DELL EMC.

Page 1 of 2

1. Which type of protocol is OSPF and what metric does it use to determine best path?

Link-state protocol that uses a concept of cost as metric

Hybrid protocol that uses hop count as a metric

Path vector protocol that uses the Dijkstra algorithm as a metric

Distance Vector protocol that uses bandwidth and delay as metric

2. What is the function of the authentication service?

Validates the user identity

Determines switch management commands

Validates switch order

Determines which services the user is enabled to access

3. A customer reports they can no longer access their services and a network administrator has been assigned to investigate. A UFD disabled error status appears on all ports.

What caused the issue?

Spanning tree Loop-guard was implemented on the uplink-state group.

One of the upstream interfaces is an uplink-state group went down.

There was no issue; this is normal behavior.

Both a port channel and its members were assigned to an uplink-state group.

4. What is an advantage of UFD?

Reduces connectivity loss.

Detects the loss of downstream connectivity.

Reduces network complexity.

Prevents the loss of upstream connectivity.

5. Which best describes traffic flow in a campus network environment?

North-East

South-West

East-West

North-South

6. Which command is used to create a non-default VRF instance?

ip vrf

ip vrf forwarding new-vrf

ip vrf forwarding vrf-test

interface ethernet 1/1/1

7. How does a DHCP Client make a request to a DHCP server following an offer?

Multicast

ACK

Broadcast

Unicast

8. Refer to the exhibit.

What is the VRRP state of OS10-A after a router with a default VRRP admin priority with VRID100 comes online?

master-state

standby-state

backup-state

primary-state

9. To which IEEE standard are dynamic LAGs compliant on Dell EMC Networking OS10 switches?

802.3af

802.3ad

802.3ac

802.3ae

10. When configuring a vrf instance for the management interface that has been in use, what step must be done first to configure it?

Configure a management route

Remove the default route

Remove all configured settings

Configure an IP Address

Page 2 of 2

11. Using the MAC 8c-ec-4b-5b-61-9d, what is a valid EUI-64 link local address?

2001::a9:8eec:4bff:fc5b:619d

fe80::a9:8cec:4bff:fe5b:619d

ff80:a9:8eec:4bff:fe5b:619d

fe80::a9:8eec:4bff:fe5b:619d

12. A network administrator is designing a Layer 2 topology and requires separate spanning-tree roots to avoid having a given port blocked for all instances.

Which spanning-tree protocols will meet this need?

STP & RSTP

RSTP-PV & MSTP

STP & RSTP-PV

RSTP & MSTP

13. Refer to the exhibit.

Which configuration will allow S1 to ping S2’s Lo0 address?

S1(config-router)# ip route 144.254.32.1 192.168.32.2/32

S1(config-router)# ip route 192.168.32.2 144.254.32.1/32

S1(config)# ip route 144.254.32.1/32 192.168.32.2

S1(config)# ip route 192.168.32.2 144.254.32.1/32

14. The network administrator wants to configure RADIUS authentication for VTY access, and for console access to use the local configuration.

Which two commands should be used to achieve this goal?

aaa authentication login vty group radius aaa authentication login console local

aaa authentication login default group radius aaa authentication login console local

aaa authentication login vty radius aaa authentication login console group local

aaa authentication login default group radius aaa authentication login console group local

15. There is a spanning tree mismatch at the global level. PVST+ is configured on a VLT peer. All VLT port channels go down on both VLT peers. A syslog error message is generated.

What is the correct action to resolve the issue?

Verify the VLT LAG ID is configured correctly on both VLT peers.

Enable RSTP on both VLT peers.

Use the show VLT detail and show VLT brief commands to view the VLT port channel status information.

Perform a mismatch check after the VLT peer is established.