Which statement describes this configuration?

Refer to the exhibit. Router 1 has established an SR-TE tunnel with router 2. Which statement describes this configuration?A . Router 1 has a list of labels used to explicitly lay out a path to router 2.B . Router 1 and router 2 have a bidirectional tunnel set up with...

January 20, 2024No CommentsREAD MORE +

What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)

What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)A . A static IPv6 address must be configured.B . A dynamic IPv6 address must be configured.C . Cisco Express Forwarding must be enabled.D . Each tunnel endpoint must support IPv4 and IPv6.E . A static IPv4 address must be...

January 20, 2024No CommentsREAD MORE +

What is the characteristic of enabling segment routing for IGPs?

What is the characteristic of enabling segment routing for IGPs?A . Segment routing must first be enabled under the routing process and then globally.B . Segment routing must first be enabled globally and then under the routing process.C . Segment routing must be enabled only globally.D . Segment routing must...

January 19, 2024No CommentsREAD MORE +

Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?

Refer to the exhibit. Router 1 is connected to router 2 on interface TenGigE0/1. Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?A . TenGigE0/1 interface provides the alternate pathB . A backup path must be statically installedC . TenGigE0/2...

January 19, 2024No CommentsREAD MORE +

Which of these can the operator use the routing policy language for, to enforce this traffic forwarding path?

Refer to the exhibit. A network operator is getting the route for 10.11.11 0/24 from two upstream providers on #XR3. The network operator must configure #XR3 to force the 10.11.11.0/24 prefix to route via next hop of 10.0.0.9 as primary when available. Which of these can the operator use the...

January 19, 2024No CommentsREAD MORE +

Where should the soft preemption be applied to solve the issue?

Refer to the exhibit. A network operator is troubleshooting TE tunnels and discovers that the soft preemption is not working as desired. Where should the soft preemption be applied to solve the issue?A . on the tail-end device for tunnel-te1 192.168.0.7B . under the tunnel-te1 interface on PE1C . explicitly...

January 19, 2024No CommentsREAD MORE +

Which BGP configuration must be added to the configuration?

Refer to the exhibit. Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?A . It must be configured for graceful restartB . It...

January 18, 2024No CommentsREAD MORE +

What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?

What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?A . traffic controllerB . path computation engineC . tail-end routerD . SNMP serverView AnswerAnswer: B

January 18, 2024No CommentsREAD MORE +

Which action makes the peering come back up again?

After an engineer configures BGP in R1, it starts receiving this message *Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1 2/6 (unacceptable hold time) 0 bytes Which action makes the peering come back up again?A . Make a soft reset to...

January 18, 2024No CommentsREAD MORE +

For which reason can two BGP peers fail to establish a neighbor relationship?

For which reason can two BGP peers fail to establish a neighbor relationship?A . Their BGP send-community strings are misconfiguredB . Their BGP timers are mismatchedC . Their remote-as numbers are misconfiguredD . They are both activated under an IPv4 address familyView AnswerAnswer: C

January 18, 2024No CommentsREAD MORE +