- All Exams Instant Download
You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?
You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?A . Lattency and JitterB . Redundancy and high availabilityC . Explicit and Implicit messagingD ....
A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)
A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)A . DLR is designed for single network operation at the machine levelB . Moving to a linear topology...
Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50?
Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50?A . ptp mode boundary ptp priority1 10 ptp priority2 50B . ptp mode boundary ptp priority1 50 ptp priority2...
How are I/O timeout and Safety I/O timeout calculated?
How are I/O timeout and Safety I/O timeout calculated?A . An I/O connection will timeout based on the lower of 4x RPI or 100ms. Safety I/O timeout is calculated as 4xRPC . An I/O connection will timeout based on the lower of 3x RPI or 100ms. Safety I/O timeout is...
Which three options are needed to configure NAT on router GW so PC1 and PC2 will be able to ping 203.0.113.1?
Refer to the exhibit. Which three options are needed to configure NAT on router GW so PC1 and PC2 will be able to ping 203.0.113.1? (Choose three)A . interface Ethernet0 ip nat inside interface Ethernet1 ip nat outsideB . ip access-list standard ACL_NAT permit 10.1.1.0 0.0.0.255C . ip nat inside...
To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?
To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?A . switch(config-if)#mls qos trust cosB . switch(config-if)#qos trust cosC . switch(config-if)#profinet cos trustD . switch(config-if)#trust qos cosView AnswerAnswer: A
Which option best describes the ProfiNET Discovery and Configuration Protocol (DCP)?
Which option best describes the ProfiNET Discovery and Configuration Protocol (DCP)?A . Can be used to override both static and dynamically (DHCP/BOOTP) assigned IP addressesB . Cannot be used to reset a device to factory defaultsC . Is only supported in Conformance Class B and C devicesD . Uses the...
Given the CIA triad elements, which ensures first that the data is encrypted and secure, second that the data is trustworthy, and third that the data is accessible by those who need it?
Given the CIA triad elements, which ensures first that the data is encrypted and secure, second that the data is trustworthy, and third that the data is accessible by those who need it?A . CIAB . ICAC . ACID . CAIView AnswerAnswer: A
What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three)
What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three)A . 3200 packets per second and 20% bandwidth for HMI and maintenance traffic.B . 2200 packets per second and 20% bandwidth for HMI and maintenance trafficC . I/O control traffic can be run...
Refer to the exhibit. Which lines represent an I/O connection running at a 20ms RPI?
Refer to the exhibit. Which lines represent an I/O connection running at a 20ms RPI?A . 2919, 2923, 2926B . 2920, 2926, 2929C . 2922, 2929, 2935D . 2914, 2915, 2916View AnswerAnswer: A
