Exhibit.
A customer is testing a dual-fabric FC SAN configuration as shown in the exhibit.
The zones are implemented on the switches shown below.
Switch 1 /Zone 1: HBA 0, LIF_1, LIF_3, LIF_5, and LIF_7
Switch 2 /Zone 2: HBA 1, LIF_2, LIF_1, LIF_6, and LIF_8
IF all the nodes are in the SLM reporting nodes list, how many paths per LUN should the customer expect when simulating a node failure by powering off Node 04?
- A . 4 paths
- B . 6 paths
- C . 8 paths
- D . 2 paths
You are asked to troubleshoot performance issues in a customer’s SAN environment. After reviewing the NetApp SAN and hosts for best practices, you have narrowed down the issues to the fabric switches.
In this scenario, which component should be verified?
- A . F_port config
- B . FLOGI database
- C . loss sig counters
- D . BB_Credit counters
Which statement is true about expanding an aggregate from 32-bit to 64-bit in place?
- A . All aggregates are automatically converted from 32-bit to 64-bit with the Data ONTAP 8.1 upgrade.
- B . The expansion is triggered by an aggr convert command.
- C . The expansion is triggered by adding disks to exceed 16 TB.
- D . The 32-bit aggregates are degraded and must be Volume SnapMirrored to a new 64-bit aggregates with Data ONTAP 8.1 upgrade.
Exhibit:
cl01::>lun resize Cvserver
svm1 Cvolume db1_vol Clun db1
-size 4096g
Error: command failed: New
size exceeds this LUN’s
initial geometry
cl01::>
What is the reason for the error shown in the exhibit?
- A . The LUN is thin provisioned, but the parent volume is thick provisioned and cannot satisfy the request.
- B . The aggregate over commitment threshold has been exceeded.
- C . The parent volume that contains the LUN is out of space.
- D . The LUN cannot be grown past its maximum resize size.
A copy of a LUN was created by using the lun copy command.
To allow the copy to be seen on the same host, what would you do?
- A . Change the serial number of the copied LUN.
- B . Configure SLM on the new node.
- C . Create a new port set.
- D . Map the LUN to the same igroup.
Exhibit:
Based on the exhibit, you are configuring a 4-node cluster with an iSCSI LIF ob each node. You connect using the first LIF from a Windows Server 2012 host.
How would you add the other three LIFs?
- A . Use the MCS button.
- B . Use the Devices button.
- C . Use the Add session button.
- D . Wait and then press the Refresh button until the other sessions appear.
Automatic host-side space management with SCSI T10 thin-provisioned LUNs is achieved by which feature of ONTAP?
- A . fractional reserve
- B . space allocation
- C . space reservation
- D . volume auto-grow
A customer has an existing large aging FC SAN environment that is reaching end of support. The environment consists of several large database servers with attached LUNs. You propose using an AFF A250, but you need to gather all end-to-end information in the current environment.
In this scenario, which resource contains this information?
- A . SAN Health Check
- B . Interoperability Matrix Tool (IMT)
- C . Active IQ OneCollect
- D . Hardware Universe (HWU)
Which exportfs command will temporarily export the resource while ignoring the options specified in the /etc/exports file?
- A . exportfs -a
- B . exportfs -i
- C . exportfs -u
- D . exportfs -v
A customer recently added two nodes with FC ports to a 4-node cluster.
Which SVM configuration is needed before the customer creates LUNs on the new nodes?
- A . The FC service needs to be enabled on the data SVM.
- B . The existing LIFs need to be migrated to the new nodes.
- C . New FC LIFs need to be created on the cluster SVM.
- D . New FC LIFs need to be created on the new nodes.
When designing a new SAN solution, which three components should be verified with the IMT? (Choose three.)
- A . the connection protocol
- B . the patch panel make and model
- C . host OS type and version
- D . the type of Ethernet switch
- E . the clustered Data ONTAP version
A company has a 4-node Data ONTAP cluster called cl01. The administrator attempts to create a volume on svm1 and can only select aggregates that are owned by node cl01-01 or cl01-02.
What is causing the problem?
- A . The SVM peering relationship has not been configured with the cl01-03 and cl01-04 HA pair.
- B . The storage virtual machine is not configured to use nodes cl01-03 or cl01-04.
- C . No LIFs have been created on nodes cl01-03 or cl01-04.
- D . Volume creation delegation is not configured to allow use of cl01-03 or cl01-04 owned aggregates.
Referring to the exhibit, which design solution is shown?
- A . single-fabric HA pair
- B . multifabric single-node
- C . single-fabric single-node
- D . multifabric HA pair
Physical Reallocation of a SnapMirror source volume increases the amount of data to transfer for the next SnapMirror update.
- A . True
- B . False
You are testing iSCSI LUN failover across a 4-node FAS9000 fabric-attached MetroCluster configuration.
In this scenario, which front end configuration is required for non-disruptive host LUN failover between sites?
- A . an intercluster LIF
- B . a stretched Layer 2 network
- C . Ipv6
- D . a stretched VSAN
You are troubleshooting a node that had a core dump. The HA partner took over and you successfully performed a giveback. You need to get access to the core files.
Which two locations will give you access? (Choose two.)
- A . /mroot/etc/crash
- B . https://<cluster-mgmt-LIF>/spi/
- C . https://<cluster-mgmt-LIF>
- D . /mroot/etc/log
Which two port personality combinations are valid for the onboard UTA2 ports on a FAS8040 controller?
- A . e0e/0e C fc
e0f/0f C fc
e0g/0g C cna
e0h/0h Ccna - B . e0e/0e C fc
e0f/0f C cna
e0g/0g C fc
e0h/0h Ccna - C . e0e/0e C fc
e0f/0f C fc
e0g/0g C fc
e0h/0h Ccna - D . e0e/0e C cna
e0f/0f Ccna
e0g/0g C fc
e0h/0h C fc
A company wants to use jumbo frames to improve performance with their iSCSI network.
When setting up the Ethernet switches for jumbo frames, which three components need to be configured?(Choose three.)
- A . Ethernet port on Management Console
- B . Ethernet port on RLM
- C . Ethernet port on host system
- D . Ethernet port on storage device
- E . Ethernet port on FC switch
- F . Ethernet switch ports being used
Click the Exhibit button.
Referring to the exhibit, which two Fibre Channel names should you zone on the FC switch to provide connectivity to the LUN? (Choose two.)
- A . 50:0a:09:82:9c:16:cc:00
- B . 50:0a:09:82:9c:7a:4e:00
- C . 20:00:00:50:56:9c:16:cc
- D . 20:01:00:50:56:9c:16:cc
An administrator suspects abnormal operation and performance-related issues within a particular SAN environment.
The administrator wants to further investigate the environment in terms of overall health, best practice recommendations, proactive remediation, and risk assessments, as compared to other SAN deployments.
Which tool should the administrator use to assess this information?
- A . Active IQ OneCollect
- B . Interoperability Matrix Tool (IMT)
- C . Active IQ
- D . Active IQ Config Advisor
What is the default RAID level for new aggregates on a DS4486?
- A . RAID-DP
- B . RAID1
- C . RAID0
- D . RAID5
Which information-gathering command should you use to gather logs for troubleshooting switch information for your Brocade switches?
- A . cfgshow
- B . fabricshow
- C . configshow
- D . supportsave
What does the space allocation argument in a LUN create command do?
- A . It thick provisions the LUN.
- B . It only disables space reclamation for the LUN.
- C . It thin provisions the LUN.
- D . It enables or disables space reclamation for the LUN.
To determine if a problem you are experiencing is known to NetApp, use the NOW site ____ utility.
- A . System Configuration Guide
- B . Bugs Online/Release Comparison
- C . AutoSupport
- D . Ethereal
Which statement best describes the output of this command?
sysstat -s 5
- A . Display the default output every five seconds and terminate after five counts.
- B . Display extended output every five seconds and print a summary after five counts.
- C . Display extended output every five seconds and print a summary upon termination.
- D . Display the default output every five seconds and print a summary upon termination.
An administrator wants to design an NVMe solution to connect Linux hosts to an ONTAP cluster. The proposed solution uses two Cisco MDS 9396T switches for each fabric in a top-of-rack design.
In this scenario, which statement is true?
- A . Asymmetric Namespace Access requires ONTAP 9.4 and higher.
- B . NVMe solutions require heterogeneous multiple switch fabrics.
- C . N_Port ID virtualization (NPIV) must be enabled on all switches.
- D . A middle-of-rack design is required.
Which resource would you use to verify whether a specific SAN configuration is supported by NetApp?
- A . ONTAP SAN Configuration Guide
- B . Interoperability Matrix Tool
- C . NetApp My AutoSupport
- D . Unified Host Utility Kit
Click the Exhibit button.
Referring to the exhibit, which switch in the fabric is the principal switch?
- A . sw10
- B . sw6
- C . sw4
- D . sw5
An administrator wants to provide isolation among physical devices connected to the same FCP fabric.
Which Cisco switch feature accomplishes this task?
- A . VSAN
- B . FSIP
- C . LUN masking
- D . logical domains
A customer’s NetApp infrastructure is reaching end-of-life (EOL), and they want to inventory their NetApp cluster. The customer wants to make sure that the proposed technical refresh satisfies their growing data demands.
Which two tools would you use to help with this recommendation? (Choose two.)
- A . Upgrade Advisor
- B . OneCollect
- C . Config Advisor
- D . Active IQ
Exhibit:
The storage system reports that one or more of the FC LIFs have the administratively up and operationally down status. Initiators are unable to connect to the affected LIFs or access LUNs that are presented by those LIFs.
Referring to the exhibit, which command fields provide port login details with the switch?
- A . conn-established
- B . media-type
- C . status-extended
- D . fabric-established
An administrator wants to implement FCoE for connectivity of an AFF A200 using VLAN 3011 for fabric traffic across VSAN 11.
When configuring the Nexus switches for FCoE connectivity, which two actions are required?(Choose two.)
- A . Create a new virtual FC interface and bind the physical interface to it.
- B . Add the virtual interface to the VSAN.
- C . Create a port channel and add all of the physical network ports that will have FCoE LIFs.
- D . Add the adapter MAC address to the network port configuration where the node is connected.
You are configuring both NVMe and FC on the same AFF A800 2-node ONTAP 9.5 cluster. You are configuring both protocols on the same Cisco FC network switches.
In this scenario, which configuration on the cluster is supported?
- A . a volume with both LUNs and namespaces
- B . an SVM with both nvme and fcp allowed protocols
- C . an AFF A800 node HBA with both NVMe/FC and FC on the same port
- D . a LIF with both fc-nvme and fcp data protocols
An administrator is adding new hosts to a vSphere cluster. The cluster uses the FC protocol to connect to a NetApp cluster. The administrator wants to configure the multipathing for the ESXi host.
Which NetApp tool should be used to accomplish this task?
- A . OnCommand System Manager (OCSM)
- B . Host Utilities
- C . SnapCenter plug-in
- D . NetApp Virtual Storage Console (VSC)
You are planning to implement a 32 Gb FC SAN on a 2-node AFF A700 ONTAP 9.5 cluster. You need to create 112 FC LIFs across the HA pair with a limit of 20 FC LIFs per physical HBA port.
In this scenario, how many 2-port 32 Gb HBA cards do you need per storage controller?
- A . 2
- B . 1
- C . 4
- D . 3
Which tool collects configuration data from hosts and switches to assist in evaluating a qualified configuration?
- A . System Manager
- B . sysstat. command
- C . SnapCenter
- D . OneCollect
A customer has decided to repurpose a NetApp FC target card from an older system. After installing the card into the newer NetApp AFF, the system kernel panics on boot.
Which tool would you use determine the problem?
- A . Active IQ OneCollect
- B . Hardware Universe (HWU)
- C . Interoperability Matrix Tool (IMT)
- D . OnCommand Insight (OCI)
A user cannot add more than one NVMe data LIF in ONTAP 9.4 on an SVM with a data protocol parameter set to nvme.
In this scenario, what is the problem?
- A . The NVMe namespace is not created
- B . Only one NVMe data LIF can be configured per SVM
- C . A demo license is used
- D . The SVM data protocol should be set to FC
To restore a qtree protected with SnapVault from the secondary storage system to the primary storage system, you can ____. (Choose two.)
- A . restore to a non existing qtree with DOT 7.2
- B . add the new qtree to the primary storage system with DOT 7.2
- C . overwrite the existing qtree on the primary storage system with DOT 7.3
- D . delete the existing qtree from the secondary storage system with DOT 7.3
Exhibit:
Referring to the exhibit, which FC LIF would cause a path failure on a host connecting to a LUN?
- A . fcp_sanluns01prod02p0g
- B . fcp_sanluns01prod02p0e
- C . fcp_sanluns01prod02p0g
- D . fcp_sanluns0lptodOlp0e
Exhibit.
You are adding a boot LUN for a new server. The server uses FCP attached through a CNA. The ONTAP cluster is also attached to the same fabric by way of UTA2. You configure the zoning for the fabric as shown in the exhibit. You discover that the server cannot see its boot LUN.
What is the problem with your zoning configuration?
- A . The zone set must have the same name as the zone.
- B . The zone was not activated.
- C . The zone used a wrong zone ID.
- D . The WWPN for the NetApp LIF is incorrect.
Exhibit.
You need to configure the SnapCenter Plug-in for VMware vSphere to back up and restore VMware datastores.
Referring to the exhibit, which additional LIF type should you create before you configure the plugin?
- A . intercluster
- B . node management
- C . SVM management
- D . cluster management
You create a 20 GB LUN in a newly created 100 GB FlexVol volume. You then write 5 GB of data to the LUN. You have space reservation disabled on the LUN.
In this scenario, how much space do you have left on the volume?
- A . 95 GB
- B . 80 GB
- C . 75 GB
- D . 85 GB
When migrating from Data ONTAP 7G to Data ONTAP 8.0 7-mode, existing non-traditional aggregates are designated as ____.
- A . 16-bit
- B . 32-bit
- C . 64-bit
- D . Foreign
- E . Unknown
You are creating a logical diagram for an FCP SAN solution.
You need to show connectivity between which three sets of components? (Choose three.)
- A . management port and ACP cabling
- B . inter-cluster network ports and hosts
- C . hosts and FCP switches
- D . hosts and FCoE switches
- E . FCP switches and storage controller
Which two commands can be used to enable LUN reservations? (Choose two.)
- A . lun set reservation
- B . lun reservation set
- C . lun map
- D . lun create
Before running lun setup on the storage system, you must first create the igroup to which the initiator will be attached.
- A . True
- B . False
On a FAS8040, which port is used for FCoE connections?
- A . e0M
- B . e0P
- C . 0a
- D . e0h
You are verifying multipathing from the host to the storage controller.
Which three components should you verify? (Choose three.)
- A . Verify that all switch ports connected to the hosts and storage devices are online using the vendor’s GUI.
- B . Verify that both FC HBA ports in the host are online using the HBA vendor’s GUI.
- C . Verify that the FC HBAs WWNN’s are in the igroup in the SVM.
- D . Verify that the SVM’s LIFs being used for multipathing are attached to the correct same physical FC port.
- E . Verify that the storage controller FC target ports status are online with the switch port showing the FC switch to which they are connected.
After applying an upgrade to the VMware cluster, you are asked to solve an issue with the Virtual Storage Console (VSC).
When attempting to create a datastore, volume errors are produced and the creation fails. As part of your troubleshooting tasks, you want to confirm that the currently installed product versions are supported.
Which tool would assist your investigation of this issue?
- A . Hardware Universe (HWU)
- B . Interoperability Matrix Tool (IMT)
- C . SAN Configuration Guide
- D . Config Advisor
Referring to the exhibit, which Linux device must be used for access to the LUN using DM-Multipath MPIO?
- A . /dev/dm-1
- B . /dev/sdc1
- C . /dev/sda1
- D . /dev/mapper/3600a09804d542d48583f456d506b386c
Which objects reside inside an igroup?
- A . host initiators
- B . LUNs
- C . qtrees
- D . volumes
Exhibit.
Referring to the exhibit, which type of zoning should be used?
- A . a WWPN with a single initiator and multiple targets
- B . a WWPN with a single initiator and a single target
- C . a WWNN with a single initiator and multiple targets
- D . a WWNN with a single Initiator and a single target
You ate deploying an 8-node FAS8200 ONTAP cluster and attaching to an existing FC fabric.
Which two ONTAP features would be used to restrict or limit the available paths seen from the host? (Choose two.)
- A . port sets
- B . igroup
- C . VLAN
- D . Selective LUN Map
You recently bought a FAS8200 series with SAS drives and want to maximize data efficiencies.
Performance is not a primary Which two statements are correct in this scenario? (Choose two.)
- A . Enable both inline and post process efficiencies.
- B . Enable always-on compaction.
- C . Enable always-on deduplication.
- D . Enable compression.
You are asked to increase the size of your existing 4-node FAS8060 cluster running ONTAP 9.7 software with four additional AFF A700 nodes.
Which tool enables you to confirm that this will be a valid addition?
- A . Active IQ OneCollect
- B . Hardware Universe (HWU)
- C . Active IQ Config Advisor
- D . Active IQ
You are planning for a new AFF A700 2-node switchless FC solution with two Cisco 9100 switches. Each AFF A700 will have one 16 Gb port connected to each Cisco 9100 switch and four FC LIFs per physical port.
You want to guarantee recovery from connection loss on a NetApp physical port and you are using single initiator to multiple target zoning.
What is the minimum number of zones required to accomplish this task?
- A . 1
- B . 2
- C . 4
- D . 8
XML-files in /etc/stats/preset are used together with the sysstat command to customize the output.
- A . True
- B . False
An administrator has expanded a 2-node ONTAP cluster to a 4-node ONTAP cluster. The cluster is using FC LUNs with all of the default settings. You must rebalance the LUNs to the new nodes.
Which configuration must be made to achieve this requirement?
- A . The new nodes must be added to the reporting nodes list.
- B . All nodes must be removed from the reporting nodes list.
- C . The original nodes must be added to the reporting nodes list.
- D . The original nodes must be removed from the reporting nodes list.
Click the Exhibit button.
An administrator enabled the FC protocol on an SVM and created a LUN for a Windows Server 2019 server. After a rescan, the LUN is not visible on the host.
Referring to the exhibit, which two steps must the administrator take to solve this problem? (Choose two.)
- A . Enable NPIV on the switch.
- B . Create an igroup, add the iSCSI IQN, and then map the igroup to the LU
- C . Disable NPIV on the switch.
- D . Create an igroup, add the WWPN of the host initiator, and then map the igroup to the LU
File locking for a CIFS client is ____.
- A . advisory
- B . mandatory
- C . ordered
- D . optional
Which statement is correct about the AFF All SAN Array (ASA)? (Choose two.)
- A . AFF ASA supports multiple protocols including NFS, FC, and NVMe over Fibre Channel.
- B . AFF ASA supports near-instantaneous unplanned failovers and givebacks.
- C . AFF ASA provides active-optimized and active-non-optimized to any LUN hosted on either controller in the HA pair.
- D . AFF ASA provides an active path to any LUN that is hosted on either controller in the HA pair.
You must ensure that a cluster that uses FabricPool has high availability.
What is required to accomplish this task?
- A . four cluster LIFs
- B . an IPspace that is dedicated to the FabricPool
- C . a local failover policy for intercluster LIFs
- D . a cloud bucket
An administrator who is using the Virtual Storage Console (VSC) creates a new FC datastore on an existing volume. While the datastore was provisioned, two hosts were in maintenance mode. When the maintenance was completed, the two hosts do not have access to the new datastore, but they have access to other datastores on the same volume.
In this scenario, what caused this result?
- A . The VSC cannot create datastores while hosts are in maintenance mode.
- B . During host maintenance, the FC HBAs were replaced with different FC HBAs.
- C . The VSC created a new igroup that contains only the hosts that were online during the datastore creation.
- D . After creation using the VSC, the administrator needs to create a LUN mapping.
Which command is used to set the configuration of an Ethernet network interface?
- A . ifconfig
- B . ifstat
- C . netstat -i
- D . sysconfig -v
Exhibit.
An administrator is configuring FCoE on Cisco Nexus switches for a new AFF A200 ONTAP cluster. The administrator executes the commands shown in the exhibit to create the necessary network configuration.
Which VLAN is responsible for controlling the FCoE traffic on the new interface?
- A . 0
- B . 3011
- C . 23
- D . 11
What is the maximum distance between a standard clustered pair at 2Gbps?
- A . 10 meters
- B . 50 meters
- C . 100 meters
- D . 500 meters
An administrator needs to determine the maximum volume size that is supported per operating system.
Which resource has this information?
- A . Interoperability Matrix Tool (IMT)
- B . OneCollect
- C . Config Advisor
- D . Hardware Universe (HWU)
An aggregate is composed of twelve 36-Gigabyte disks. A drive fails and only 72-Gigabyte spare disks are available. Data ONTAP will then perform what action.
- A . Chooses a 72-Gigabyte disk and use it as is.
- B . Chooses a 72-Gigabyte disk and right-size it.
- C . Halts after 24 hour of running in degraded mode.
- D . Alerts you that there are no 36-Gigabyte disks and wait for one to be inserted.
Exhibit:
cl01::>igroup show Cvserver
svm1
VserverIgroup Protocol OS
Type Initiators ——— ————- ——
— ——— —————–
——————–
svm1 esx_cluster mixed vmware
20:00:00:25:b5:11:a0:01,
20:00:00:25:b5:11:b0:01,
iqn.1998-01.com.vmware:esx02
cl01::>
A customer is provisioning storage for two ESXi hosts using FCoE with CNA adapters. The customer mapped the LUN to the igroup shown in the exhibit. After scanning for new devices, the LUN is only seen by one of the ESXi hosts.
What caused the problem?
- A . One of the hosts is added in the igroip via iSCSI IQN.
- B . The igroup protocol needs to be configured as FCP.
- C . The switch zoning configuration does not include the correct initiators.
- D . The LIFs are not on their home ports.
Exhibit:
cl01::>igroup show Cvserver
svm1
VserverIgroup Protocol OS
Type Initiators ——— ————- ——
— ——— —————–
——————–
svm1 esx_cluster mixed vmware
20:00:00:25:b5:11:a0:01,
20:00:00:25:b5:11:b0:01,
iqn.1998-01.com.vmware:esx02
cl01::>
A customer is provisioning storage for two ESXi hosts using FCoE with CNA adapters. The customer mapped the LUN to the igroup shown in the exhibit. After scanning for new devices, the LUN is only seen by one of the ESXi hosts.
What caused the problem?
- A . One of the hosts is added in the igroip via iSCSI IQN.
- B . The igroup protocol needs to be configured as FCP.
- C . The switch zoning configuration does not include the correct initiators.
- D . The LIFs are not on their home ports.
Exhibit:
cl01::>igroup show Cvserver
svm1
VserverIgroup Protocol OS
Type Initiators ——— ————- ——
— ——— —————–
——————–
svm1 esx_cluster mixed vmware
20:00:00:25:b5:11:a0:01,
20:00:00:25:b5:11:b0:01,
iqn.1998-01.com.vmware:esx02
cl01::>
A customer is provisioning storage for two ESXi hosts using FCoE with CNA adapters. The customer mapped the LUN to the igroup shown in the exhibit. After scanning for new devices, the LUN is only seen by one of the ESXi hosts.
What caused the problem?
- A . One of the hosts is added in the igroip via iSCSI IQN.
- B . The igroup protocol needs to be configured as FCP.
- C . The switch zoning configuration does not include the correct initiators.
- D . The LIFs are not on their home ports.
Exhibit:
cl01::>igroup show Cvserver
svm1
VserverIgroup Protocol OS
Type Initiators ——— ————- ——
— ——— —————–
——————–
svm1 esx_cluster mixed vmware
20:00:00:25:b5:11:a0:01,
20:00:00:25:b5:11:b0:01,
iqn.1998-01.com.vmware:esx02
cl01::>
A customer is provisioning storage for two ESXi hosts using FCoE with CNA adapters. The customer mapped the LUN to the igroup shown in the exhibit. After scanning for new devices, the LUN is only seen by one of the ESXi hosts.
What caused the problem?
- A . One of the hosts is added in the igroip via iSCSI IQN.
- B . The igroup protocol needs to be configured as FCP.
- C . The switch zoning configuration does not include the correct initiators.
- D . The LIFs are not on their home ports.
Exhibit:
cl01::>igroup show Cvserver
svm1
VserverIgroup Protocol OS
Type Initiators ——— ————- ——
— ——— —————–
——————–
svm1 esx_cluster mixed vmware
20:00:00:25:b5:11:a0:01,
20:00:00:25:b5:11:b0:01,
iqn.1998-01.com.vmware:esx02
cl01::>
A customer is provisioning storage for two ESXi hosts using FCoE with CNA adapters. The customer mapped the LUN to the igroup shown in the exhibit. After scanning for new devices, the LUN is only seen by one of the ESXi hosts.
What caused the problem?
- A . One of the hosts is added in the igroip via iSCSI IQN.
- B . The igroup protocol needs to be configured as FCP.
- C . The switch zoning configuration does not include the correct initiators.
- D . The LIFs are not on their home ports.
Add the AFF A700 HA pair to the reporting-nodes list.
What is the correct sequence in performing, these steps?
- A . 1, 2, 3, 4
- B . 4, 1, 2, 3
- C . 4, 3, 2, 1
- D . 3, 2, 1, 4
You are planning to expand a SAN-only ONTAP 9.5 cluster that consists of eight AFF A700 nodes.
In this scenario, what is the maximum number of additional AFF A700 nodes that would be added?
- A . 2
- B . 4
- C . 8
- D . 0
You have an AFF A220 cluster connected to a dual fabric topology. You must ensure that SAN hosts do not lose access to LUNs during unplanned failures.
Which two operations should be performed to accomplish this task? (Choose two.)
- A . Manually set all LUNs offline.
- B . Manually set all FC LIFs on a single node to "down".
- C . Turn the power off on one disk shelf.
- D . Initiate a reboot of one Fibre Channel switch.
Which data collection tool would be used for obtaining detailed information about hosts that are attached to ONTAP storage?
- A . Upgrade Advisor
- B . OneCollect
- C . Brocade Network Advisor
- D . Conflg Advisor
Exhibit.
You are asked to change the iSCSl Target Node Name of an SVM named SVM1 that is serving data.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A . Reconnect all the lUNs alter renaming the target node.
- B . Disable Selective LUN Mapping (SIM) and create port sets.
- C . Unmap and re-map the LUNs.
- D . Stop and start the iSCSI service.
A customer is using both FC and NVMe in a cluster. The customer needs to do some work on AFF_1.
Referring to the exhibit, what will happen?
- A . The NVMe namespaces on AFF_2 will be available after takeover of AFF_1.
- B . The FC LUNs that use cluster interconnect to access the LUNs on AFF_1 will be unavailable after failover.
- C . The FC LUNs on node AFF_2 will be unavailable after failover of AFF_1.
- D . The NVMe namespaces on AFF_1 will be unavailable after takeover by AFF_2.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
UNIX allows file access based on ____.
- A . NT ACLs and UNIX permissions.
- B . NT ACLs and SID.
- C . GID or UID and UNIX permissions.
- D . GID or UID and ACLs.
Create datastore and its containing LUNS and volumes.
In step 8, you are not able to see the LUNs you provisioned on your storage controller. When you run igroup show you see the ESX host’s initiators; however, they are listed “not logged in”.
What is the problem?
- A . You need to configure ALUA.
- B . The LUN was not put online.
- C . The LUN type is not set to type VMware.
- D . You need to configure zoning.
Which command provides information on Snapshot copy auto delete variables?
- A . -volume modify -space-mgmt-try-first autodelete-
- B . -volume snapshot autodelete show-
- C . -volume show-
- D . -volume file clone autodelete-
You have an SVM with FC access and you want to create a LUN.
When creating the LUN, which statement is true?
- A . The volume containing the LUN should be a FlexGroup volume.
- B . You should map the LUN to multiple portsets.
- C . The volume containing the LUN should be a FlexVol volume.
- D . The volume containing the LUN should be a traditional volume.
Which two components must be verified for a supported NetApp SAN confutation? (Choose two.)
- A . host memory
- B . host GPU
- C . host multipath
- D . host bus adapter
The OSSV agent on the primary system listens to TCP port 10000 for all SnapVault communications.
- A . True
- B . False
Exhibit:
You are asked to serve iSCSI LUNs in an existing SVM on your AFF A220 using ONTAP 9.5. You verified that the iSCSI license is configured on your cluster and that the iSCSI protocol is enabled.
Referring to the exhibit, what is needed to allow hosts to log into the iSCSI target?
- A . Create new LIFs with the iSCSI data protocol.
- B . Create new igroups with the host IQNs.
- C . Add iSCSI to the data protocol of the existing LIFs.
- D . Map LUNs to the igroups.
A customer is planning to connect a Linux server to a FAS8200 using Brocade FC switches. During the initial configuration, the SVM does not log in to the fabric.
Which two statements are correct in this scenario? (Choose two.)
- A . NPIV has not been enabled on the switches.
- B . The switch port topology is set incorrectly to the E_Port.
- C . ALUA has not been set up on the FAS8200.
- D . Zoning is incorrectly configured between the Linux server and the ONTAP cluster.
You plan to use Foreign LUN Import (FLI) to migrate data from an older storage array to an ONTAP cluster. You have properly cabled the storage array and the NetApp nodes to your dual-fabric SAN.
Which two steps are required for this migration and cutover? (Choose two.)
- A . Add NetApp WWN initiator ports to the existing zones.
- B . Add NetApp WWN target ports to the existing zones so that your hosts can access both storage arrays.
- C . Create two zones that contain the NetApp target ports and the host initiators ports, one for each fabric.
- D . Create two zones that contain NetApp initiator ports and the source storage target ports, one for each fabric.
You plan to use Foreign LUN Import (FLI) to migrate data from an older storage array to an ONTAP cluster. You have properly cabled the storage array and the NetApp nodes to your dual-fabric SAN.
Which two steps are required for this migration and cutover? (Choose two.)
- A . Add NetApp WWN initiator ports to the existing zones.
- B . Add NetApp WWN target ports to the existing zones so that your hosts can access both storage arrays.
- C . Create two zones that contain the NetApp target ports and the host initiators ports, one for each fabric.
- D . Create two zones that contain NetApp initiator ports and the source storage target ports, one for each fabric.
75 GB
Used Size: 144 KB
Used Percentage: 5%
Volume Nearly Full Treshold
Percent: 95%
Volume Full Treshold
Percent: 98%
Maximum Autosize (for
flexvolvs only): 6GB
(DEPRECATED) CAutosize
Increment (for flexvolvs
only): 256MB
Minimum Autosize: 5GB
Autosize Grow Threshold
Percentage: 85%
Autosize Shrink Threshold
Percentage: 50%
Autosize Mode: off
Autosize Enabled (for
flexvolvs only): false
Space Guarantee Style: volume
Space Guarantee in Effect:
true
Snapshot Directory Access
Enabled: true
Space Reserved for Snapshot
Copies: 5%
Snapshot Reserve Used: 0%
Snapshot Policy: none
Node name: cl01-01
Reserved Space for
Overwrites: 0B
Fractional Reserve: 100%
Primary Space Management
Strategy: volume_grow
Total Physical Used Size:
144KB
Physical Used Percentage: 0%
A customer has a volume with the configuration shown in the exhibit.
What will happen if the volume vs_iscsi_exch01 reaches 85% used?
- A . The volume will delete snapshots until 20% is free in the volume.
- B . The volume will automatically grow up to 6 GB.
- C . The volume will no longer be accessible from the host.
- D . The volume will continue working as expected.
Referring to the exhibit, what happens when you change the type for port 1a from target to initiator?
- A . The port type for 1a changes to initiator, and you must reboot the controller for the changes to take effect.
- B . You receive an error message that you must take ports 1a and 1b offline before you can change the type.
- C . The port type for 1a and 1b changes to initiator, and you must reboot the controller for the changes to take effect.
- D . You receive an error message that you must take the port 1a offline before you can change the type.
You need to configure iSCSI on your existing ONTAP cluster in a new SVM. The iSCSI LUNs will be served over a new Layer 2 network using the same physical ports that also use the CIFS protocol on a different SVM.
Which two actions should you perform to accomplish this task? (Choose two.)
- A . Create a new portset.
- B . Create a new VLAN.
- C . Create a new broadcast domain.
- D . Create a new AD object.
Which command disables client access to Snapshot copies on a volume called flexvoll?
- A . cifs shares-change flxvoll-nosnap
- B . snap access flexvoll off
- C . vol options flexvoll nonsnapdir on
- D . vol options flexvoll snapdir off
- E . vol options flexvoll snapdir on
Referring to the exhibit, which two LIFs would be optimized paths to LUN /vol/OraDev_Vol/OraDev? (Choose two.)
- A . aff_node-01_0g_A
- B . aff_node-02_0e_A
- C . aff_node-02_0g_A
- D . aff_node-01_0e_A
A company has 20 ESX hosts. Ten of the hosts are connected using FC, and the rest are connected over iSCSI. The FC host HBA queue depth is set to 32, and the iSCSI LUN queue depth is set to 64. The FC hosts are now experiencing random connectivity issues.
In this scenario, what would be the reason for the disconnects?
- A . The FC host has a lower queue depth.
- B . According to the IMT, unsupported HBA firmware is in use.
- C . All of the hosts are part of the same cluster.
- D . The queue depth is not consistent across the cluster.
A 4-node ONTAP FAS9000 cluster was used to serve I/O from six RedHat 7.3 servers. The servers were configured with maximum, queue depth.
For production purposes, an additional 60 similarly configured hosts were added to the environment. Later, the hosts started reporting random QFull errors, and the aggregated performance degraded.
Which two solutions would alleviate the QFull errors and performance problems? (Choose two.)
- A . Remove Selective LUN Mapping (SIM) from the 4-node FAS9000 cluster.
- B . Download the latest FC HBA driver, firmware, and BIOS, and deploy them on the hosts.
- C . Configure and use additional FC target HBAs in the FAS9000 cluster.
- D . Reduce FC HBA gueue depth on the hosts.
Which two scenarios in deploying ONTAP Cloud are supported by the Cloud Manager tool? (Choose two.)
- A . ONTAP Cloud deployed as an HA pair on IBM Cloud
- B . ONTAP Cloud deployed as an HA pair on VMware
- C . ONTAP Cloud deployed as a single instance on Microsoft Azure
- D . ONTAP Cloud deployed as an HA pair on Amazon Web Services
You are troubleshooting high CPU use on a FAS8200 with all SAS HDDs. You have SAN hosts with LUNs in a volume named vol1. You want to reduce CPU use and maintain storage efficiencies.
Referring to the exhibit which three actions will accomplish this task? (Choose three.)
- A . Disable compression.
- B . Enable cross-volume deduplication.
- C . Disable inline deduplication.
- D . Enable post process deduplication.
- E . Enable data compaction.
While expanding a 200 GB LUN in an ONTAP 9.4 system, the following error is observed:
What is the cause of this error?
- A . The volume auto-grow is disabled.
- B . The LUN reached maximum capacity.
- C . The LUN can be expanded up to 10 times its original size.
- D . Space reservation is enabled.
What is the recommended minimum of data LIFs per node for iSCSI in a dual-fabric configuration with four SVMs?
- A . 8
- B . 12
- C . 16
- D . 4
Which Data ONTAP option sets system-wide throttling for all transfers?
- A . options transfer.wide.enable
- B . options transfer.throttle.enable
- C . options replication.wide.enable
- D . options replication.throttle.enable
An administrator is migrating from a third-party’s SAN to a newly purchased FAS9000. The administrator decides to use the NetApp Foreign LUN Import (FLI) process.
What must the administrator do for this process to work properly?
- A . Create multiple igroups for the Initiator ports.
- B . Create six distinct zones that include specific ports within each zone.
- C . Zone target ports of source storage with initiator ports of destination storage.
- D . Make the destination LUN larger than the foreign LUN.
When using a Protection Manager policy to manage Open Systems SnapVault backups on a UNIX server, which three are valid objects to include in the data set? (Choose three.)
- A . A file
- B . A qtree
- C . A directory
- D . Theentire client
You have an SVM that serves LUNs to your hosts in an FC SAN environment. This SVM runs on a 4-node cluster and has two data LIFs on each node, according to best practices. You just created a LUN and mapped it to your initiators group. The LUN is owned by node01.
In this scenario, what would be an appropriate test for LUN mobility?
- A . Move the LUN to node02.
- B . Mirror the LUN to another node in your cluster.
- C . Physically disconnect the SAN ports, and verify if the SAN data LIFs automatically move to other hosts.
- D . Copy the LUN to another node and create a new LUN map.