What is the status of the virtual server?

An LTM Specialist configures a new virtual server with a single pool member. The LTM Specialist has NOT defined a health monitor for the pool, pool member or node. What is the status of the virtual server?A . Available (Enabled)B . Offline (Disabled)C . Unavailable (Enabled)D . Unknown (Enabled)View AnswerAnswer:...

February 15, 2021 No Comments READ MORE +

What is causing the change in failover state to occur?

TWO LTM devices are in the same Device Group and configured for Ac live/Standby Failover. The LTM Specialist observes that the HA Active and Standby device constantly changes state. All network links use the default route domain A dedicated fiber ink is used for the HA connection with a latency...

February 15, 2021 No Comments READ MORE +

What should the LTM Specialist do to resolve this problem?

An LTM Specialist creates an Analytics wide to show the type of browsers used to access a certain application. However, the generated statistics only sum up all transaction for that application under one item called ‘ Aggregated.’’ What should the LTM Specialist do to resolve this problem?A . Verify that...

February 15, 2021 No Comments READ MORE +

What needs to be completed before applying that configuration change?

An LTM Specialist needs to apply SNAT using currently used SNAT pool to a new virtual server. What needs to be completed before applying that configuration change?A . Review connection for the selected SNAT pool and enlarge it if appropriateB . Make sure that the BIG-IP device is NOT operating...

February 15, 2021 No Comments READ MORE +

Which virtual server type should an LTM Specialist configure on the LTM device?

A LTM device needs to load balance active and passive FTP traffic while using only a single virtual server. Which virtual server type should an LTM Specialist configure on the LTM device?A . Forwarding (Layer 2)B . StandardC . StatelessD . DHCP relayE . Forwarding (IP)View AnswerAnswer: E

February 15, 2021 No Comments READ MORE +

Which configuration item enables this behavior?

One LTM device in an HA pair of LTM devices is unable to reach its default gateway. An HA Failover event needs to happen. Which configuration item enables this behavior?A . iRuleB . Gateway Fail SafeC . Gateway pool monitorD . Gateway poolView AnswerAnswer: B

February 15, 2021 No Comments READ MORE +

What is a complete list of profiles that must be applied to the virtual server for this iRule?

Refer to the following iRule: What is a complete list of profiles that must be applied to the virtual server for this iRule?A . Fast L4, HTTPB . TCP, HTTPC . TCP, HTTP, Client SSLD . Fast L4 , HTTP, StreamView AnswerAnswer: B

February 14, 2021 No Comments READ MORE +

What is the maximum number of guests that the LTM Specialist should upgrade at once?

An LTM Specialist needs to upgrade all guests on a Viprion eight CMP guests. What is the maximum number of guests that the LTM Specialist should upgrade at once?A . EightB . OneC . TWOD . FourView AnswerAnswer: B Explanation: Explanation Each guest is independent, just like hardware upgrades. Can...

February 14, 2021 No Comments READ MORE +

What must the LTM Specialist consider before implementing the configuration change?

An LTM Specialist plans to enable connection mirroring for a virtual server in an HA environment. What must the LTM Specialist consider before implementing the configuration change?A . Impact on system performance that might be noticeableB . The add-on license that is required for this feature to be availableC ....

February 14, 2021 No Comments READ MORE +

What is the resulting status of this pool member?

Refer to the exhibit. The http monitor is applied to a pool All members are enabled One pool member stops responding TCP port 80. The server still responds to ping. What is the resulting status of this pool member?A . Available (Enabled)B . Offline (Disabled)C . Unavailable (Disabled)D . Unknown...

February 14, 2021 No Comments READ MORE +