- All Exams Instant Download
What does the output confirm?
Refer to the exhibit. A network engineer configures NAT on R1 and enters the show command to verity the configuration. What does the output confirm?A . The first pocket triggered NAT to add on entry to NAT table B. R1 is configured with NAT overload parameters C. A Telnet from...
What are two effects of this configuration?
Refer to the exhibit. What are two effects of this configuration? (Choose two.)A . R1 becomes the active router. B. R1 becomes the standby router. C. If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online. D. If R1 goes down. R2 becomes active...
Which feature must be configured to remedy the issue?
A company has an existing Cisco 5520 HA cluster using SSO. An engineer deploys a new single Cisco Catalyst 9800 WLC to test new features. The engineer successfully configures a mobility tunnel between the 5520 cluster and 9800 WLC. Client connected to the corporate WLAN roam seamlessly between access points...
Which AP mode allows an engineer to scan configured channels for rogue access points?
Which AP mode allows an engineer to scan configured channels for rogue access points?A . sniffer B. monitor C. bridge D. localView AnswerAnswer: B
Which two threats does AMP4E have the ability to block? (Choose two.)
Which two threats does AMP4E have the ability to block? (Choose two.)A . DDoS B. ransomware C. Microsoft Word macro attack D. SQL injection E. email phishingView AnswerAnswer: B,C Explanation: https://www.cisco.com/c/dam/en/us/products/collateral/security/amp-for-endpoints/c11-742008-00-cisco-amp-for-endpoints-wp-v2a.pdf
Which configuration commands can the engineer use to allow this traffic without disrupting existing traffic flows?
Refer to the exhibit. An engineer must modify the access control list EGRESS to allow all IP traffic from subnet 10.1.10.0/24 to 10.1.2.0/24. The access control list is applied in the outbound direction on router interface GigabitEthemet 0/1. Which configuration commands can the engineer use to allow this traffic without...
What is one fact about Cisco SD-Access wireless network deployments?
What is one fact about Cisco SD-Access wireless network deployments?A . The access point is part of the fabric underlay B. The WLC is part of the fabric underlay C. The access point is part the fabric overlay D. The wireless client is part of the fabric overlayView AnswerAnswer: C
Which characteristic distinguishes Ansible from Chef?
Which characteristic distinguishes Ansible from Chef?A . Ansible lacs redundancy support for the master server. Chef runs two masters in an active/active mode. B. Ansible uses Ruby to manage configurations. Chef uses YAML to manage configurations. C. Ansible pushes the configuration to the client. Chef client pulls the configuration from...
Which configuration establishes EBGP neighborship between these two directly connected neighbors and exchanges the loopback network of the two routers through BGP?
Refer to the exhibit. Which configuration establishes EBGP neighborship between these two directly connected neighbors and exchanges the loopback network of the two routers through BGP?A . R1(config)#router bgp 1 R1(config-router)#neighbor 192.168.10.2 remote-as 2 R1(config-router)#network 10.1.1.0 mask 255.255.255.0 R2(config)#router bgp 2 R2(config-router)#neighbor 192.168.10.1 remote-as 1 R2(config-router)#network 10.2.2.0 mask 255.255.255.0 B....
In a wireless Cisco SD-Access deployment, which roaming method is used when a user moves from one access point to another on a different access switch using a single WLC?
In a wireless Cisco SD-Access deployment, which roaming method is used when a user moves from one access point to another on a different access switch using a single WLC?A . Layer 3 B. inter-xTR C. auto anchor D. fast roamView AnswerAnswer: B Explanation: A fabric edge node provides onboarding...
