Cisco 350-501 Implementing and Operating Cisco Service Provider Network Core Technologies Online Training
Cisco 350-501 Online Training
The questions for 350-501 were last updated at Sep 15,2025.
- Exam Code: 350-501
- Exam Name: Implementing and Operating Cisco Service Provider Network Core Technologies
- Certification Provider: Cisco
- Latest update: Sep 15,2025
Refer to the exhibit:
What does the REST API command do?
- A . It retrieves the information requested by Descriptions xml
- B . It removes the information identified by Descriptions xml
- C . It executes the commands specified in Descriptions xml
- D . It displays the information identified by Descriptions xml
Why do packet loops occur during the configuration of BlDlR-PIM?
- A . The network does not support BIDIR-PIM
- B . The network is partially upgraded to support BIDlR-PIM
- C . No interface for carrying traffic for multicast groups has been configured
- D . The router has not been configured to advertise itself
Refer to the exhibit:
This output is included at the end of an output that was provided by a device using NETCONF.
What does the code show?
- A . It shows the hostname of the device as rpc-reply
- B . It shows that the running configuration is blank
- C . It shows NETCONF uses remote procedure calls.
- D . It shows that the full configuration is being modeled by VANG
Refer to the exhibit:
What is the URL used for with REST API?
- A . It is used to contact a URL filter to determine the efficacy of a web address
- B . It is used to send a TACACS+ authentication request to a server
- C . It is used to send a message to the APIC to perform an operation on a managed object or class operator
- D . It is used to initiate an FTP session to save a running configuration of a device.
You are configuring MPLS traffic-engineering tunnels in the core.
Which two ways exist for the tunnel path across the core? (Choose two )
- A . Tunnel links inherit IGP metrics by default unless overridden
- B . Tunnels can be configured with dynamic path or explicitly defined path
- C . A zero bandwidth tunnel is not a valid option
- D . The bandwidth statement creates a "hard" reservation on the link-The dynamic path option is supported only with IS-IS
When configuring traffic engineering tunnels in Cisco MPLS core network, you see the traffic is not taking the expected path in the core.
Which command do you use to quickly check path of a TE tunnel?
- A . Traceroute mpls ipv4 -tunnel destination
- B . Ping <tunnel destination IP>
- C . show mpls traffic-engineering tunnels
- D . traceroute <tunnel destination IP>
Refer to the exhibit:
If router RA is configured as shown, which IPv4 multicast address space does it use?
- A . 224.0. 0.0/8
- B . 225.0. 0.0/8
- C . 232.0. 0.0/8
- D . 239.0. 0.0/8
Refer to the exhibit:
P3 and PE4 are at the edge of the service provider core and serve as ABR routers Aggregation areas are on either side of the core.
Which statement about the architecture is true?
- A . If each area is running its own IGP. the ABR routers must redistribute the IGP routing table into BGP
- B . To support seamless MPLS. TDP must be used as the label protocol
- C . If each area is running its own IGP. BGP must provide an end-to-end MPLS LSP
- D . To support seamless MPLS, the BGP route reflector feature must be disabled
Refer to the exhibit:
Which statement about this configuration is true?
- A . It requires an explicit Cisco MPLS TE path to be configured for the tunnel to run
- B . It requires OSPF to also be running to have optimized Cisco MPLS TE tunnels
- C . It requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run
- D . It is the configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing
Latest 350-501 Dumps Valid Version with 248 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
