Cisco 350-401 Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) Online Training
Cisco 350-401 Online Training
The questions for 350-401 were last updated at Nov 03,2025.
- Exam Code: 350-401
- Exam Name: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)
- Certification Provider: Cisco
- Latest update: Nov 03,2025
Which device makes the decision for a wireless client to roam?
- A . wireless client
- B . wireless LAN controller
- C . access point
- D . WCS location server
How is MSDP used to interconnect multiple PIM-SM domains?
- A . MSDP depends on BGP or multiprotocol BGP for mterdomam operation
- B . MSDP SA request messages are used to request a list of active sources for a specific group
- C . SDP allows a rendezvous point to dynamically discover active sources outside of its domain
- D . MSDP messages are used to advertise active sources in a domain
Refer to the Exhibit.
A network engineer must configure a password expiry mechanism on the gateway router for all local passwords to expire after 60 days.
What is required to complete this task?
- A . The password expiry mechanism is on the AAA server and must be configured there.
- B . Add the aaa authentication enable default Administrators command.
- C . Add the username admin privilege 15 common-criteria*policy Administrators password 0 Cisco13579! command.
- D . No further action Is required. The configuration is complete.
Which action is the vSmart controller responsible for in an SD-WAN deployment?
- A . handle, maintain, and gather configuration and status for nodes within the SD-WAN fabric
- B . distribute policies that govern data forwarding performed within the SD-WAN fabric
- C . gather telemetry data from vEdge routers
- D . onboard vEdge nodes into the SD-WAN fabric
DRAG DROP
Drag and drop the Qos mechanisms from the left to the correct descriptions on the right
What is the function of the LISP map resolver?
- A . to send traffic to non-LISP sites when connected to a service provider that does not accept nonroutable ElDs as packet sources
- B . to connect a site to the LISP-capable part of a core network publish the EID-to-RLOC mappings for the site, and respond to map-request messages
- C . to decapsulate map-request messages from ITRs and forward the messages to the MS.
- D . to advertise routable non-LISP traffic from one address family to LISP sites in a different address family
A network administrator applies the following configuration to an IOS device.
What is the process of password checks when a login attempt is made to the device?
- A . A TACACS+server is checked first. If that check fail, a database is checked?
- B . A TACACS+server is checked first. If that check fail, a RADIUS server is checked. If that check fail. a local database is checked.
- C . A local database is checked first. If that fails, a TACACS+server is checked, if that check fails, a RADUIS server is checked.
- D . A local database is checked first. If that check fails, a TACACS+server is checked.
What is the purpose of the LISP routing and addressing architecture?
- A . It creates two entries for each network node, one for Its identity and another for its location on the network.
- B . It allows LISP to be applied as a network visualization overlay though encapsulation.
- C . It allows multiple Instances of a routing table to co-exist within the same router.
- D . It creates head-end replication used to deliver broadcast and multicast frames to the entire network.
How does Cisco Trustsec enable more access controls for dynamic networking environments and data centers?
- A . classifies traffic based on advanced application recognition
- B . uses flexible NetFlow
- C . classifies traffic based on the contextual identity of the endpoint rather than its IP address correct
- D . assigns a VLAN to the endpoint
Refer to the exhibit.
A network engineer configures a GRE tunnel and enters the show Interface tunnel command.
What does the output confirm about the configuration?
- A . The keepalive value is modified from the default value.
- B . Interface tracking is configured.
- C . The tunnel mode is set to the default.
- D . The physical interface MTU is 1476 bytes.
Latest 350-401 Dumps Valid Version with 404 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
Question 91 has a wrong answer marked s correct. The answer is B.
BPDU filter is the only option to block BPDUs while not going inte err disabled when a BPDU is received.
https://www.exam4training.com/which-command-set-must-be-configured-on-switch1-to-achieve-the-following-results-on-port-fa0-1/
https://www.cisco.com/en/US/docs/switches/metro/me3600x_3800x/trash/swstpopt.html#:~:text=The%20BPDU%20filtering%20feature%20can,bpdufilter%20default%20global%20configuration%20command.