Cisco 350-401 Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) Online Training
Cisco 350-401 Online Training
The questions for 350-401 were last updated at Sep 16,2025.
- Exam Code: 350-401
- Exam Name: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)
- Certification Provider: Cisco
- Latest update: Sep 16,2025
DRAG DROP
Drag and drop the descriptions from the left onto the QoS components on the right.
While configuring an IOS router for HSRP with a virtual IP of 10 1.1.1. an engineer sees this log message.
Which configuration change must the engineer make?
- A . Change the HSRP group configuration on the local router to 1.
- B . Change the HSRP virtual address on the local router to 10.1.1.1.
- C . Change the HSRP virtual address on the remote router to 10.1.1.1.
- D . Change the HSRP group configuration on the remote router to 1.
What is the function of a fabric border node in a Cisco SD-Access environment?
- A . To collect traffic flow information toward external networks
- B . To connect the Cisco SD-Access fabric to another fabric or external Layer 3 networks
- C . To attach and register clients to the fabric
- D . To handle an ordered list of IP addresses and locations for endpoints in the fabric.
A network engineer configures BGP between R1 and R2. Both routers use BGP peer group CORP and are set up to use MD5 authentication.
This message is logged to the console of router R1:
“ May 5 39:85:55.469: %TCP-6-BADAUTH ” Invalid MD5 digest from 10.10.10.1 (29832) to 10.120.10.1 (179) tebleid -0
Which two configuration allow peering session to from between R1 and R2? Choose two.)
- A . R1(config-router)#neighbor 10.10.10.1 peer-group CORP
R1(config-router)#neighbor CORP password Cisco - B . R2(config-router)#neighbor 10.120.10.1 peer-group CORP
R2(config-router)#neighbor CORP password Cisco - C . R2(config-router)#neighbor 10.10.10.1 peer-group CORP
R2(config-router)#neighbor PEER password Cisco - D . R1(config-router)#neighbor 10.120.10.1 peer-group CORP
R1(config-router)#neighbor CORP password Cisco - E . R2(config-router)#neighbor 10.10.10.1 peer-group CORP
R2(config-router)#neighbor CORP password Cisco
Which two operational models enable an AP to scan one or more wireless channels for rouge access points and at the same time provide wireless services to clients? (Choose two.)
- A . Rouge detector
- B . Sniffer
- C . FlexConnect
- D . Local
- E . Monitor
What are two benefits of virtual switching when compared to hardware switching? (Choose two.)
- A . increased MTU size
- B . hardware independence
- C . VM-level isolation
- D . increased flexibility
- E . extended 802.1Q VLAN range
which entity is a Type 1 hypervisor?
- A . Oracle VM VirtualBox
- B . VMware server
- C . Citrix XenServer
- D . Microsoft Virtual PC
Refer to the Exhibit.
How was spanning-tree configured on this interface?
- A . By entering the command spanning-tree portfast trunk in the interface configuration mode.
- B . By entering the command spanning-tree portfast in the interface configuration mode
- C . By entering the command spanning-tree mst1 vlan 10,20,30,40 in the global configuration mode
- D . By entering the command spanning-tree vlan 10,20,30,40 root primary in the interface configuration mode
What is a characteristic of a next-generation firewall?
- A . only required at the network perimeter
- B . required in each layer of the network
- C . filters traffic using Layer 3 and Layer 4 information only
- D . provides intrusion prevention
Which features does Cisco EDR use to provide threat detection and response protection?
- A . containment, threat intelligence, and machine learning
- B . firewalling and intrusion prevention
- C . container-based agents
- D . cloud analysis and endpoint firewall controls
Latest 350-401 Dumps Valid Version with 404 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
Question 91 has a wrong answer marked s correct. The answer is B.
BPDU filter is the only option to block BPDUs while not going inte err disabled when a BPDU is received.
https://www.exam4training.com/which-command-set-must-be-configured-on-switch1-to-achieve-the-following-results-on-port-fa0-1/
https://www.cisco.com/en/US/docs/switches/metro/me3600x_3800x/trash/swstpopt.html#:~:text=The%20BPDU%20filtering%20feature%20can,bpdufilter%20default%20global%20configuration%20command.