Cisco 350-401 Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) Online Training
Cisco 350-401 Online Training
The questions for 350-401 were last updated at Sep 15,2025.
- Exam Code: 350-401
- Exam Name: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)
- Certification Provider: Cisco
- Latest update: Sep 15,2025
A network administrator has designed a network with two multilayer switches on the distribution layer, which act as default gateways for the end hosts.
Which two technologies allow every end host in a VLAN to use both gateways? (Choose two)
- A . GLBP
- B . HSRP
- C . MHSRP
- D . VSS
- E . VRRP
Refer to the Exhibit.
An engineer attempts to configure a trunk between switch sw1 and switch SW2 using DTP, but the trunk does not form.
Which command should the engineer apply to switch SW2 to resolve this issue?
- A . switchport mode dynamic desirable
- B . switchport nonegotiate
- C . no switchport
- D . switchport mode access
In cisco SD_WAN, which protocol is used to measure link quality?
- A . OMP
- B . BFD
- C . RSVP
- D . IPsec
Refer to the Exhibit.
An engineer configures a new HSRP group. While reviewing the HSRP status, the engineer sees the logging message generated on R2.
Which is the cause of the message?
- A . The same virtual IP address has been configured for two HSRP groups
- B . The HSRP configuration has caused a spanning-tree loop
- C . The HSRP configuration has caused a routing loop
- D . A PC is on the network using the IP address 10.10.1.1
Which measure is used by an NTP server to indicate its closeness to the authoritative time source?
- A . latency
- B . hop count
- C . time zone
- D . stratum
What is the output of this code?
- A . username Cisco
- B . get_credentials
- C . username
- D . CISCO
An engineer runs the code against an API of Cisco DMA Center, and the platform returns this output What does the response indicate?
- A . The authentication credentials are incorrect
- B . The URl string is incorrect.
- C . The Cisco DNA Center API port is incorrect
- D . The HTTP method is incorrect
Refer to the Exhibit.
Which configuration must be applied to R to enable R to reach the server at 172.16.0.1?
- A . interface Ethernet0/0
ip address 172.16.0.7 255.255.0.0
router ospf 44 vrf bank
network 172.16.0.0 255.255.0.0 - B . interface Ethernet0/0
vrf forwarding hotel
ip address 172.16.0.7 255.255.0.0
router ospf 44 vrf Hotel
network 172.16.0.0 0.0.255.255 area 0 - C . interface Ethernet0/0
vrf forwarding bank
ip address 172.16.0.7 255.255.0.0
router ospf 44 vrf bank
network 172.16.0.0 0.0.255.255 area 0 - D . interface Ethernet0/0
ip address 172.16.0.7 255.255.0.0
router ospf 44 vrf hotel
network 172.16.0.0 255.255.0.0
DRAG DROP
Drag and drop the wireless elements on the left to their definitions on the right.
Refer to the exhibit.
An engineer has configured Cisco ISE to assign VLANs to clients based on their method of authentication, but this is not working as expected.
Which action will resolve this issue?
- A . require a DHCP address assignment
- B . utilize RADIUS profiling
- C . set a NAC state
- D . enable AAA override
Latest 350-401 Dumps Valid Version with 404 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
Question 91 has a wrong answer marked s correct. The answer is B.
BPDU filter is the only option to block BPDUs while not going inte err disabled when a BPDU is received.
https://www.exam4training.com/which-command-set-must-be-configured-on-switch1-to-achieve-the-following-results-on-port-fa0-1/
https://www.cisco.com/en/US/docs/switches/metro/me3600x_3800x/trash/swstpopt.html#:~:text=The%20BPDU%20filtering%20feature%20can,bpdufilter%20default%20global%20configuration%20command.