Cisco 300-430 Implementing Cisco Enterprise Wireless Networks (ENWLSI) Online Training
Cisco 300-430 Online Training
The questions for 300-430 were last updated at Oct 23,2025.
- Exam Code: 300-430
- Exam Name: Implementing Cisco Enterprise Wireless Networks (ENWLSI)
- Certification Provider: Cisco
- Latest update: Oct 23,2025
An engineer must configure MSE to provide guests access using social media authentication.
Which service does the engineer configure so that guests use Facebook credentials to authenticate?
- A . Social Connect
- B . Client Connect
- C . Visitor Connect
- D . Guest Connect
A network engineer has been hired to perform a new MSE implementation on an existing network. The MSE must be installed in a different network than the Cisco WLC.
Which configuration allows the devices to communicate over NMSP?
- A . Allow UDP/16113 port on the central switch.
- B . Allow TCP/16113 port on the firewall.
- C . Allow UDP/16666 port on the VPN router.
- D . Allow TCP/16666 port on the router.
What is the default NMSP echo interval between Cisco MSE and a Wireless LAN Controller?
- A . 10 seconds
- B . 15 seconds
- C . 30 seconds
- D . 60 seconds
An engineer just added a new MSE to Cisco Prime Infrastructure and wants to synchronize the MSE with the Cisco 5520 WLC, located behind a firewall in a DMZ. It is noticed that NMSP messages are failing between the two devices.
Which traffic must be allowed on the firewall to ensure that the MSE and WLC are able to communicate using NMSP?
- A . TCP 1613
- B . UDP 16113
- C . UDP 1613
- D . TCP 16113
Refer to the exhibit.
An engineer needs to configure location services in an office. The requirement is to use FastLocate and achieve higher locations refresh rates.
Which location-based technique should be implemented?
- A . probe-based
- B . location patterning
- C . data packet-based
- D . angulation
An engineer is managing a wireless network for a shopping center. The network includes a Cisco WLC, a Cisco MSE, and a Cisco Prime Infrastructure.
What is required to use Cisco CMX Location Analytics?
- A . Enable tracking parameters in Cisco MSE.
- B . Enable Context Aware and CMX Browser Engage.
- C . Install Cisco Prime Infrastructure with floor maps.
- D . Set history parameters in Cisco MSE.
An engineer configures a deployment to support:
✑ Cisco CMX
✑ licenses for at least 3000 APs
✑ 6000 wIPS licenses
The Cisco vMSE appliance must be sized for this deployment.
Which Cisco vMSE Release 8 option must the engineer deploy?
- A . Large vMSE
- B . Low-End vMSE
- C . Standard vMSE
- D . High-End vMSE
A new MSE with wIPS service has been installed and no alarm information appears to be reaching the MSE from controllers.
Which protocol must be allowed to reach the MSE from the controllers?
- A . SOAP/XML
- B . NMSP
- C . CAPWAP
- D . SNMP
Which two statements about the requirements for a Cisco Hyperlocation deployment are true? (Choose two.)
- A . After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.
- B . NTP can be configured, but that is not recommended.
- C . The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.
- D . The Cisco Hyperlocation feature must be enabled only on the wireless LAN controller.
- E . If the Cisco CMX server is a VM, a high-end VM is needed for Cisco Hyperlocation deployments.
An engineer is performing a Cisco Hyperlocation accuracy test and executes the cmxloc start command on Cisco CMX.
Which two parameters arerelevant? (Choose two.)
- A . X, Y real location
- B . client description
- C . AP name
- D . client MAC address
- E . WLC IP address
Latest 300-430 Dumps Valid Version with 109 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
