Cisco 300-360 Designing Cisco Wireless Enterprise Networks Online Training
Cisco 300-360 Online Training
The questions for 300-360 were last updated at Sep 09,2025.
- Exam Code: 300-360
- Exam Name: Designing Cisco Wireless Enterprise Networks
- Certification Provider: Cisco
- Latest update: Sep 09,2025
An engineer has been assigned the task of deciding the cell overlap for a wireless voice deployment.
Which Cisco measurement recommendation should be considered?
- A . The edge of the cell should be -67 dBm.
- B . One AP should be deployed per 3000 square feet.
- C . The edge of the cell should be below 35 RSSI.
- D . The measurement should be done on the 2.4-GHz band.
Which three components and tasks should be considered while planning the site survey? (Choose three.)
- A . Determine the project scope, type of deployment, timeline, scale, budget, and users
- B . Determine project stakeholders
- C . Determine customer training requirements
- D . Determine AP and controller placement
- E . Determine the customer applications that the network will support
- F . Determine radio spectrum and channel allocation
- G . Schedule customer end user interviews
A customer reports that wireless clients are not able to receive multicast data from known working multicast servers on the wired network. The client is connecting at the highest mandatory wireless rate of 24 Mbps and the wireless controller is configured for multicast-unicast mode.
What three actions should the engineer take next to troubleshoot the issue? (Choose three.)
- A . verify that the L3 interfaces are configured for pim sparse-dense-mode on the VLAN servicing the wireless access points as well as the wireless controller’s management VLAN
- B . change the wireless controller from Multicast-Unicast mode to Multicast-Multicast mode and assign a multicast address in the 239.X.X.X/8 subnet
- C . verify that IGMP snooping is disabled on the wireless controller since the access points are handling IGMP messages from the clients
- D . verify that Global Multicast mode has been enabled
- E . make sure the highest mandatory rate is set to 54 Mbps so that the multicast traffic has sufficient bandwidth
- F . verify Multicast Listener Discovery (MLD) v1 snooping has been enabled to keep track of and deliver IPv4 multicast flows
After implementing mesh with an IP surveillance camera connected to the LAN port on a RAP, the engineer notices that QoS is not being marked. In this setup, what device is responsible for marking upstream traffic from the camera?
- A . IP Camera
- B . MAP
- C . RAP
- D . Wireless Controller
- E . First-Hop Router
When calculating bandwidth usage for an application, what two values represent the minimum and maximum 802.11 overhead per frame? (Choose two.)
- A . 16 bytes
- B . 24 bytes
- C . 28 bytes
- D . 48 bytes
- E . 56 bytes
- F . 60 bytes
- G . 64 bytes
When planning to perform a customer WLAN site survey, which three components and tasks should be considered? (Choose three.)
- A . Schedule a meeting with the customer to discuss the Statement of Work
- B . Complete the Pre-Survey Customer Questionnaire
- C . Schedule customer end user interviews
- D . Consider travel, access, and equipment requirements necessary to perform the site survey
- E . Schedule initial customer meeting and pre-survey walkthrough events
- F . Determine radio spectrum and channel allocation
- G . Determine AP and controller placement
- H . Determine customer training requirements
Which option will allow the maximum 2.4 GHz channel usage for a survey and voice deployment in the ETSI domain?
- A . 1, 6, 11
- B . 1, 5, 9, 13
- C . 1, 6, 9, 14
- D . 1, 6, 11, 14
A corporation has a Cisco Unified Wireless Network that has been deployed for voice coverage. The wireless data rates have been tuned to mandatory rates of 18 Mbps and 36 Mbps. Some wireless clients have been experiencing drops streaming multicast video while moving throughout the building.
What is the cause of the drop in video?
- A . Clients are maintaining a 12Mbps rate and cannot receive the stream at 18Mbps.
- B . Clients are not roaming due to coverage. This is causing the multicast data to drop due to the client reassociating often.
- C . Clients are roaming at lower data rates and are not maintaining 36Mbps connectivity.
- D . Clients are connected at 18Mbps; however, other clients are connecting at 12Mbps and are causing the multicast video to degrade.
Clients are experiencing artifacts in multicast video even though the network was recently upgraded to 802.11n APs.
What three configuration changes will be most effective to improve performance? (Choose three.)
- A . increase mandatory data rate
- B . enable 40 MHz wide channels
- C . enable Call Admission Control
- D . increase QoS marking on multicast
- E . enable VideoStream
- F . disable Multicast Messaging
You have a multinational customer that would like you to perform a wireless site survey for a new manufacturing facility in Singapore. They have had a local vendor install a point -to- point wireless bridge link between two buildings 1 km apart. The ground between the buildings is flat but because facilities are in the mountains, dense fog is an issue. There is no line of sight issues between the buildings. The link is experiencing errors and throughput issues. Currently the two radios are set to operate at 2.4 GHz and the transmit power is set to 7 dBm with 7 dBm antennas.
What do you need to take into consideration when performing the site survey for this link?
- A . Change the radio power to 17 dBm.
- B . Change the radio power to 20 dBm and replace with a 16 dBm antenna.
- C . Change the radio power to 29 dBm.
- D . Change the radio power to 13 dBm.
Latest 300-360 Dumps Valid Version with 221 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
