Cisco 300-360 Designing Cisco Wireless Enterprise Networks Online Training
Cisco 300-360 Online Training
The questions for 300-360 were last updated at Sep 08,2025.
- Exam Code: 300-360
- Exam Name: Designing Cisco Wireless Enterprise Networks
- Certification Provider: Cisco
- Latest update: Sep 08,2025
An engineer is determining the signal levels for the wireless cells.
Which signal-to-noise ratio is an optimal configuration to achieve?
- A . minimum SNR of -33 dBm
- B . minimum SNR of -25 dBm
- C . minimum SNR of 25 dB
- D . minimum SNR of 33 dB
While performing a Layer 1 passive wireless site survey of a location an engineer detects several instances of low power frequency hopping interference, but cannot physically locate the interfering device or devices.
Why is the engineer unable to locate the offending device or devices?
- A . The sources are nearby narrow-beam radar and are sweeping through the facility.
- B . The sources are PAN and are mobile.
- C . The sources are above the ceiling file and transmit intermittently.
- D . The sources are actually high-powered devices and transmit from off the site.
An engineer must design wireless coverage in thick-walled stairwells.
Which information should the engineer refer to when determining where APs can be installed?
- A . Local or National Building Code
- B . IEEE
- C . BICSI TDMM
- D . Cisco Hardware Installation Guide
A customer has a business-critical voice network and wants to be alerted whenever voice clients move out of a coverage area and experience RSSI below -67 dBm on the 5 GHz band.
Which option can be configured on the wireless controller to alert network administrators when this limit is surpassed?
- A . EDCA; voice optimized
- B . SIP voice sample interval
- C . 802.11a voice RSSI coverage threshold
- D . traffic stream metrics
A hospital environment was designed to guarantee RF coverage at or better than -67 dBm in the 5 GHz spectrum. The customer mandates that RRM be used for DCA and TPC in both bands. After deployment, why do many of the legacy 802.11b/g devices have difficulty maintaining connectivity?
- A . Excessive co-channel interference in the 2.4 GHz band exists.
- B . Excessive overlapping channels in the 2.4 GHz band exists.
- C . TPC drastically reduces Tx power in the 2.4 GHz band.
- D . TCP drastically increases Tx power in the 2.4 GHz band.
A network engineer is configuring QoS with a DSCP value of 46. To which queue must the CoS be mapped for priority queuing of the voice frames?
- A . 1
- B . 2
- C . 5
- D . 4
- E . 3
An engineer is deploying an outdoor Mesh network.
Which four major factors should be considered? (Choose four.)
- A . power
- B . buildings
- C . traffic lights
- D . satellite dishes
- E . line of sight
- F . network connectivity
- G . power lines
- H . mounting
When designing a WLAN, AP placement is important.
Which option describes how to rank the density of APs needed to support location services versus data and voice services?
- A . Data services have the lowest density of APs compared to location services, which has the highest density.
- B . Data services have a lower density of APs compared to location services, but more than voice.
- C . Voice services have the highest density of APs over location and data services.
- D . Voice and data services require a higher density of APs than location services.
You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data.
How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?
- A . Use the centralized deployment method in the data center with the N + N redundancy method.
- B . Use the centralized deployment method in the data center with the N + 1 redundancy method
- C . Use the centralized deployment method in the data center with the 1 + 1 redundancy method and client SSO.
- D . Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
- E . Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
- F . Use the distributed deployment method in each building MDF with the N + N redundancy method.
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data.
What does this indicate about the signal strength?
- A . The area is below the minimum threshold configured on the tool.
- B . The area is below the detectable level and indicates no RF signal.
- C . The area is below -100 dBm at coverage cell edge.
- D . The area is below -67 dBm at coverage cell edge.
Latest 300-360 Dumps Valid Version with 221 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
