Cisco 300-075 Implementing Cisco IP Telephony & Video, Part 2 v1.0 Online Training
Cisco 300-075 Online Training
The questions for 300-075 were last updated at Oct 23,2025.
- Exam Code: 300-075
- Exam Name: Implementing Cisco IP Telephony & Video, Part 2 v1.0
- Certification Provider: Cisco
- Latest update: Oct 23,2025
Which two statements regarding IPv4 Static NAT address 209.165.200.230 has been configured on a VCS Expressway are true? (Choose two.)
- A . The Advanced Networking or Dual Network Interfaces option key has been installed.
- B . VCS rewrites the Layer 3 source address of outbound SIP and H.323 packets to 209.165.200.230.
- C . VCS applies 209.165.200.230 to outbound SIP and H.323 payload messages.
- D . With static NAT enabled on the LAN2 interface, VCS applies 209.165.200.230 to outbound H.323 and SIP payload traffic exiting the LAN1 interface.
Which configuration does Cisco recommend for the peer address on the Expressway-C secure traversal zone when the Expressway-E has one NIC enabled?
- A . Expressway-E internal IP address
- B . Expressway-E external IP address
- C . Expressway-E internal FQDN
- D . Expressway-E external FQDN
If delegated credentials checking has been enabled and remote workers can register to the Expressway, which statement is true?
- A . H.323 message credential checks are delegated.
- B . SIP registration proxy mode is set to On in the Expressway.
- C . A secure neighbor zone has been configured between the Expressway and the Expressway Control.
- D . SIP registration proxy mode is set to Off in the Expressway.
Which two options should be used to create a secure traversal zone between the Expressway-C and Expressway-E? (Choose two.)
- A . Expressway-C and Expressway-E must trust each other’s server certificate.
- B . One Cisco Unified Communications traversal zone for H.323 and SIP connections.
- C . A separate pair of traversal zones must be configured if an H.323 connection is required and Interworking is disabled.
- D . Enable username and password authentication verification on Expressway-E.
- E . Create a set of username and password on each of the Expressway-C and Expressway-E to authenticate the neighboring peer.
Which two statements regarding you configuring a traversal server and traversal client relationship are true? (Choose two.)
- A . VCS supports only the H.460.18/19 protocol for H.323 traversal calls.
- B . VCS supports either the Assent or the H.460.18/19 protocol for H.323 traversal calls.
- C . VCS supports either the Assent or the H.460.18/19 protocol for SIP traversal calls.
- D . If the Assent protocol is configured, a TCP/TLS connection is established from the traversal client to the traversal server for SIP signaling.
- E . A VCS Expressway located in the public network or DMZ acts as the firewall traversal client.
What is the standard Layer 3 DSCP media packet value that should be set for Cisco TelePresence endpoints?
- A . CS3 (24)
- B . EF (46)
- C . AF41 (34)
- D . CS4 (32)
When you configure QoS on VCS, which settings do you apply if traffic through the VCS should be tagged with DSCP AF41?
- A . Set QoS mode to DiffServ and tag value 32.
- B . Set QoS mode to IntServ and tag value to 34.
- C . Set QoS mode to DiffServ and tag value 34.
- D . Set QoS mode to IntServ and tag value to 32.
- E . Set QoS mode to ToS and tag value to 32.
What is the default DSCP/PHB for video conferencing packets in Cisco Unified Communications Manager?
- A . EF/46
- B . CS6/48
- C . AF41/34
- D . CS3/24
The administrator at Company X is getting user reports of inconsistent quality on video calls between endpoints registered to Cisco Unified Communications Manager. The administrator runs a wire trace while a video call is taking place and sees that the packets are not set to AF41 for desktop video as they should be.
Where should the administrator look next to confirm that the correct DSCP markings are being set?
- A . on the MGCP router at the edge of both networks
- B . the service parameters in the VCS Control
- C . the QoS service parameter in Cisco Unified Communications Manager
- D . on the actual Cisco phone itself because the DSCP setting is not part of its configuration file downloaded at registration
- E . The setting cannot be changed for video endpoints that are registered to Cisco Unified Communications Manager, but only when they are registered to the VCS Control.
Which three commands are necessary to override the default CoS to DSCP mapping on interface Fastethernet0/1? (Choose three.)
- A . mls qos map cos-dscp 0 10 18 26 34 46 48 56
- B . mls qos map dscp-cos 8 10 to 2
- C . mls qos
- D . interface Fastethernet0/1 mls qos trust cos
- E . interface Fastethernet0/1 mls qos cos 1
- F . interface Fastethernet0/2 mls qos cos 1
Latest 300-075 Dumps Valid Version with 520 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
