BICSI RCDD-002 BICSI Registered Communications Distribution Designer – RCDD Online Training
BICSI RCDD-002 Online Training
The questions for RCDD-002 were last updated at Jul 18,2025.
- Exam Code: RCDD-002
- Exam Name: BICSI Registered Communications Distribution Designer - RCDD
- Certification Provider: BICSI
- Latest update: Jul 18,2025
The RJ-45 is now known as the 8P8C style connector, per the Telecommunications Industry Association (TIA) standard.
What does the P and C stand for?
- A . Plug and connector
- B . Position and connector
- C . Position and contact
- D . Plug and contact
What type of fiber optic cable is manufactured to protect individual glass strands and is primarily designed for use inside buildings?
- A . Ribbon
- B . Tight buffered
- C . Loose tube
- D . Air blown
You must extend a video systems backbone coax cable that was recently installed.
Which of the following coaxial cable types would provide the best performance for both analog and digital video?
- A . Series 6
- B . Series 11
- C . RG 16
- D . RG 59
- E . RG 62
Which of the following is true about screened twisted pair cable assemblies?
- A . The drain wire and screen foil must be bonded at one end only.
- B . The drain wire and screen foil must be bonded at every connection.
- C . There is no need to bond the screen foil or drain because it is not important.
- D . The drain wire and screen foil must be separately bonded at opposite ends.
This type of cable is an unbalanced system:
- A . Unshielded twisted-pair (UTP)
- B . Shielded twisted-pair (STP)
- C . Screened twisted-pair (ScTP)
- D . Coaxial
There are three buildings approximately 400 meters apart and the customer wants to use 10 Gig Ethernet.
What fiber should be specified for this application?
- A . 8 – 9 micron singlemode
- B . 50 micron multimode
- C . 50 micron laser optimized multimode
- D . 62.5 micron multimode
The ability of a conductors insulation to transmit an electric field is called:
- A . Conductivity
- B . Transmitability
- C . Permittivity
- D . Capacitance
- E . Reactance
You are extending 1000 MHz video service from your existing headend to a new equipment room (ER). Your existing incoming video signal is plus (+) 15 dBmV. You have three two- way splitters with a total of minus (-) 15 dB. You are adding 122 m (400 ft) of series 11 (RG 11) cable with a minus (-) 18 dB with eight single end F-connectors with a total of minus (-) 1.2 dB.
From the selections below, what is the MINIMUM gain amplifier required in the headend room?
- A . Plus (+) 15 dB
- B . Plus (+) 20 dB
- C . Plus (+) 25 dB
- D . Plus (+) 30 dB
- E . Plus (+) 35 dB
A
Topic 4, Work Areas
When specifying telecommunications outlet boxes, all of the following should be considered EXCEPT:
- A . Outlet box shall be a minimum of 100 mm (4 in) x 100 mm (4 in) x 76 mm (3 in)
- B . Outlet boxes should be installed near an electric outlet at the same height
- C . Different outlet boxes have different support requirements
- D . Floor mounted telecom outlet boxes should be coordinated with furniture to minimize the potential trip hazard
- E . Outlet boxes must be of adequate size so that minimum cable bend radius requirements are not exceeded
The MINIMUM separation distance between grounded metal telecommunications pathway and unshielded power lines is:
- A . 75 mm (3 in)
- B . 150 mm (6 in)
- C . 300 mm (12 in)
- D . 610 mm (24 in)
- E . 1220 mm (48 in)
Latest RCDD-002 Dumps Valid Version with 361 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
