Based on the exhibit, which action does FortiGate take?

Refer to the exhibit. Based on the exhibit, which action does FortiGate take?A . FortiGate bounces port5 after it detects all SD-WAN members as dead.B . FortiGate fails over to the secondary device after it detects all SD-WAN members as dead.C . FortiGate brings up port5 after it detects all...

October 3, 2024 No Comments READ MORE +

What are three mandatory post-run tasks that must be performed?

The SD-WAN overlay template helps to prepare SD-WAN deployments. To complete the tasks performed by the SD-WAN overlay template, the administrator must perform some post-run tasks. What are three mandatory post-run tasks that must be performed? (Choose three.)A . Create policy packages for branch devices.B . Assign an sdwan_id metadata...

October 3, 2024 No Comments READ MORE +

Which two statements are correct about the health check status on this FortiGate device?

Exhibit. The exhibit shows the output of the command diagnose sys sdwan health-check status collected on a FortiGate device. Which two statements are correct about the health check status on this FortiGate device? (Choose two.)A . The health-check VPN_PING orders the members according to the lowest jitter.B . The interface...

October 2, 2024 No Comments READ MORE +

In the exhibit, which statement best describes the configuration applied to the FortiGate device?

Refer to the exhibit. An administrator used the SD-WAN overlay template to prepare an IPsec configuration for a hub-and-spoke SD-WAN topology. The exhibit shows the installation preview for one FortiGate device. In the exhibit, which statement best describes the configuration applied to the FortiGate device?A . It is a hub...

October 2, 2024 No Comments READ MORE +

Which two interfaces are considered overlay links? (Choose two.)

Which two interfaces are considered overlay links? (Choose two.)A . LAGB . IPsecC . PhysicalD . GREView AnswerAnswer: BD

October 1, 2024 No Comments READ MORE +

Based on the output shown in the exhibits, which two reasons can cause the observed behavior?

Refer to the exhibits. Exhibit A shows the packet duplication rule configuration, the SD-WAN zone status output, and the sniffer output on FortiGate acting as the sender. Exhibit B shows the sniffer output on a FortiGate acting as the receiver. The administrator configured packet duplication on both FortiGate devices. The...

October 1, 2024 No Comments READ MORE +

What are two common use cases for remote internet access (RIA)? (Choose two.)

What are two common use cases for remote internet access (RIA)? (Choose two.)A . Provide direct internet access on spokesB . Provide internet access through the hubC . Centralize security inspection on the hubD . Provide thorough inspection on spokesView AnswerAnswer: BC Explanation: B. Provide internet access through the hub:...

September 30, 2024 No Comments READ MORE +

Which are two benefits of using CLI templates in FortiManager? (Choose two.)

Which are two benefits of using CLI templates in FortiManager? (Choose two.)A . You can reference meta fields.B . You can configure interfaces as SD-WAN members without having to remove references first.C . You can configure FortiManager to sync local configuration changes made on the managed device, to the CLI...

September 30, 2024 No Comments READ MORE +

Which two statements about the SD-WAN zone configuration are true? (Choose two.)

Which two statements about the SD-WAN zone configuration are true? (Choose two.)A . The service-sla-tie-break setting enables you to configure preferred member selection based on the best route to the destination.B . You can delete the default zones.C . The default zones are virtual-wan-link and SASE.D . An SD-WAN member...

September 29, 2024 No Comments READ MORE +

Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to exchange routes over IPsec?

Refer to the exhibit. Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to exchange routes over IPsec?A . type must be set to static.B . mode-cfg must be enabled.C . exchange-interface-ip must be enabled.D . add-route must be disabled.View AnswerAnswer: D

September 28, 2024 No Comments READ MORE +