In this scenario, which two methods will limit the total number of paths to eight paths per LUN?

You have a 2-node FAS900 cluster with six FC LIFs per node. In this scenario, which two methods will limit the total number of paths to eight paths per LUN? (Choose two.)A . FC queue depthB . Port setsC . SLMD . FC switch zoningView AnswerAnswer: B,C

February 10, 2018 No Comments READ MORE +

In this scenario, which three steps are required to move the FC LIF so it is available on another node?

You need to take a cluster node down for extended maintenance, but you want to the FC LIF to avoid re-zoning the switch fabric. In this scenario, which three steps are required to move the FC LIF so it is available on another node? (Choose three.)A . Use the network...

February 9, 2018 No Comments READ MORE +

Which NetApp resource would you use to validate the maximum number of FC hops that are supported by a switch vendor?

Which NetApp resource would you use to validate the maximum number of FC hops that are supported by a switch vendor?A . Hardware UniverseB . Switch Install GuideC . Installation and Setup Instructions PosterD . SAN Configuration GuideView AnswerAnswer: D

February 6, 2018 No Comments READ MORE +

Referring to the exhibit, how much space is allocated for the volume in the parent aggregate?

An administrator has a volume that was created with the storage efficiency features shown in the volume show output. Inside the volume, the administrator creates LUNs lun1 and iun2 lun1 is a 20GB LUN with space reservation enabled. Iun2 is a 30GB LUN with space reservation disabled. 10 GB of...

February 4, 2018 No Comments READ MORE +

Referring to the volume v_iscsi_exch01 shown in the exhibit, which two LUN combinations can you create? (Choose two.)

Referring to the volume v_iscsi_exch01 shown in the exhibit, which two LUN combinations can you create? (Choose two.) A . Five LUNS, each LUN 3GB in size, with the LUN option space-reserve set to enabledB . Three LUNS, each LUN 5GB in size, with the LUN option space-reserve set to...

February 1, 2018 No Comments READ MORE +

You need to add the new LIF WWPNs to which object?

You are adding new nodes to an ONTAP cluster. You need to add the new LIF WWPNs to which object?A . Reporting nodesB . Failover groupC . VLAND . Switch zoneView AnswerAnswer: D

January 31, 2018 No Comments READ MORE +

In this scenario, which non-disruptive action would accomplish this task?

A 4-node cluster is upgraded from clustered Data ONTAP 8.2 to ONTAP 9.1. LUNs that were created after the upgrade are visible only on the target ports of the node that owns the LUN and its HA partner. LUNs that were on the system before the upgrade are visible on...

January 29, 2018 No Comments READ MORE +

Which three components must be verified in the IMT to ensure a support FC configuration? (Choose three.)

Which three components must be verified in the IMT to ensure a support FC configuration? (Choose three.)A . The FC HBA that is installed in the hostB . The OS patch level or service packC . The volume manager that is being used on the hostD . The size and...

January 27, 2018 No Comments READ MORE +

To allow the copy to be seen on the same host, what would you do?

A LUN copy has been created by using the lun copy command. To allow the copy to be seen on the same host, what would you do?A . Create a new portset.B . Map the LUN to the same igroup.C . Change the serial number of the copied LUE ....

January 24, 2018 No Comments READ MORE +

Where do you identify the disk shelves and disks that are supported for a specific controller model?

Where do you identify the disk shelves and disks that are supported for a specific controller model?A . Hardware Universe (HWU)B . Interoperability Matrix Tool (IMT)C . Disk and Aggregates Power guideD . Installation and Setup Instructions posterView AnswerAnswer: A

January 23, 2018 No Comments READ MORE +