- All Exams Instant Download
What are the correct steps to accomplish this?
A network administrator must configure a virtual IP address using VRRP on interface VLAN 100 within OS10. What are the correct steps to accomplish this?A . OS10(config)# interface vlan 100 OS10(conf-if-vl-100)# ip address 10.0.100.1/24 OS10(conf-if-vl-100)# standby-group 256 OS10(conf-vlan100-vrid-256)# standby-address 10.0.100.2B . OS10(config)# interface vlan 100 OS10(conf-if-vl-100)# ip address 10.0.100.2/24 OS10(conf-if-vl-100)#...
How will the reload of these switches proceed to result in the default initial state?
Two (2) Dell EMC Networking OS10 switches in a VLT configuration need to be upgraded. How will the reload of these switches proceed to result in the default initial state?A . Reload the primary VLT node. This process will automatically trigger the reload of the secondary node after it has...
What could be the cause of this issue?
A network administrator has recently configured eBGP to use source addressing from its loopback interfaces. Customers later report that eBGP routes are not being learned. What could be the cause of this issue?A . BGP devices must be configured with the multihop command when using loopback interfacesB . BGPv4 does...
In a PIM Sparse Mode (PIM-SM) based multicast topology, what function does the Rendezvous Point provide?
In a PIM Sparse Mode (PIM-SM) based multicast topology, what function does the Rendezvous Point provide?A . The node is used to provide IGMP snooping across a layer 3 boundary.B . The root node of the source tree topology is used to provide routing between the source and receiver.C ....
What is the minimum multicast configuration level required on the router?
A router needs to be configured to allow multiple multicast servers for the same group to be presented only to ports where active listeners reside. Each listener may exclude non-preferred servers. What is the minimum multicast configuration level required on the router?A . IGMPv3 without snooping PIM-SSMB . IGMPv2 with...
What are the correct commands that configure the DHCP lease from pool DC1 to never expire?
What are the correct commands that configure the DHCP lease from pool DC1 to never expire?A . OS10(config)# ip dhcp server OS10(config-dhcp)# pool DC1 accounting OS10(config-dhcp-DC1)#no lease expireB . OS10(config)# ip dhcp server OS10(config-dhcp)# pool DC1 accounting OS10(config-dhcp-DC1)# no expireC . OS10(config)#dhcp server OS10(config-dhcp)# pool DC1 OS10(config-dhcp-DC1)# no lease expireD...
Which multicast address do all OSPF routers use?
Which multicast address do all OSPF routers use?A . 224.0.0.6B . 239.0.0.6C . 239.0.0.4D . 224.0.0.5View AnswerAnswer: D
Which command mode allows configuration of switches L2 and L3 interfaces?
Which command mode allows configuration of switches L2 and L3 interfaces?A . EXEC ModeB . InterfaceC . ConfigurationD . GlobalView AnswerAnswer: B
Match the IGMP versions and features in the source column to the feature or version where they first appeared. There are more packet descriptions than IGMP versions.
Match the IGMP versions and features in the source column to the feature or version where they first appeared. There are more packet descriptions than IGMP versions.A . IGMP Version 1 - a) Queries can be sent out either as general queries or group-specific queries IGMP Version 2 - b)...
What is an advantage of running LLDP?
What is an advantage of running LLDP?A . Automatic error detection and correction of the portB . Reduces spanning-tree convergenceC . Provides detailed software version informationD . Simplifies the use of network managementView AnswerAnswer: D
