- All Exams Instant Download
Which four options are the basic troubleshooting steps that you should use to troubleshoot this issue?
You are having problems browsing to http://www.cisco.com from your laptop that is running Windows. Your laptop is connected directly to a default gateway, which is a Cisco ISR G2 router. Which four options are the basic troubleshooting steps that you should use to troubleshoot this issue? (Choose four.)A . Issue...
What are three features present on both ICMPv4 and ICMPv6? (Choose three.)
What are three features present on both ICMPv4 and ICMPv6? (Choose three.)A . Connectivity testsB . Address assignmentC . Information error messagingD . Address resolutionE . Mobile IPv4 supportF . Multicast group managementG . Mobile IPv6 supportH . Fragmentation needed notificationView AnswerAnswer: A,C,H
Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure?
Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure?A . Rapid Per-VLAN Spanning Tree ProtocolB . Resilient Ethernet ProtocolC . Multiple Spanning Tree ProtocolD . Spanning Tree ProtocolView AnswerAnswer: B
This show output is from the S7 Cisco Metro Switch and the PE7 Cisco ASR 9000 Series Router. Which configuration change(s) is/are needed to bring the S7 FastEthernet 0/2 interface into the up/up state?
This show output is from the S7 Cisco Metro Switch and the PE7 Cisco ASR 9000 Series Router. Which configuration change(s) is/are needed to bring the S7 FastEthernet 0/2 interface into the up/up state? *Mar 20 21:28:02.177: %ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD: Collisions at FastEthernet0/2 exceed threshold. Considered as loop-back. *Mar 20 21:28:02.177: %PM-4-ERR_DISABLE:...
Which two protocols could be used during this communication?
The network administrator is using a Windows PC application that is called putty.exe for remote communication to a switch for network troubleshooting. Which two protocols could be used during this communication? (Choose two).A . SNMPB . HTTPC . TelnetD . RMONE . SSHView AnswerAnswer: C,E
Which Cisco IOS XR CLI command can you use to determine if the firmware on any of the line cards on the Cisco ASR 9000 Series Router needs to be upgraded?
Which Cisco IOS XR CLI command can you use to determine if the firmware on any of the line cards on the Cisco ASR 9000 Series Router needs to be upgraded?A . RP/0/RSP0/CPU0:PE1#show platformB . RP/0/RSP0/CPU0:PE1(admin)#show platformC . RP/0/RSP0/CPU0:PE1#show hw-module fpd location allD . RP/0/RSP0/CPU0:PE1#show versionE . RP/0/RSP0/CPU0:PE1(admin)#show versionF ....
Which feature is used to protect the control plane of the router?
Which feature is used to protect the control plane of the router?A . Port securityB . uRPFC . Routing protocol authenticationD . VRFE . SSHF . SSLView AnswerAnswer: C
Which Cisco IOS XR command is involved in enabling remote access?
Which Cisco IOS XR command is involved in enabling remote access?A . RP/0/RSP0/CPU0:PE1(config)# router staticB . RP/0/RSP0/CPU0:PE1(config)# line console 0C . RP/0/RSP0/CPU0:PE1(config)# vrf defaultD . RP/0/RSP0/CPU0:PE1(config)# telnet ipv4 server max-servers 20E . RP/0/RSP0/CPU0:PE1(config)# username CISCO password LABView AnswerAnswer: D
Given the IP address 10.106.170.145 255.248.0.0, which three options are the subnet that this IP address belongs to, the host IP address range on this subnet, and the subnet broadcast IP address?
Given the IP address 10.106.170.145 255.248.0.0, which three options are the subnet that this IP address belongs to, the host IP address range on this subnet, and the subnet broadcast IP address?A . subnet = 10.104.0.0/13B . subnet = 10.106.0.0/13C . subnet = 10.112.0.0/13D . host IP address range =...
What command is required on the customer Switched Virtual Interface (SVI) to allow clients to receive addresses from this server?
A centralized DHCP server has been setup for customer use. What command is required on the customer Switched Virtual Interface (SVI) to allow clients to receive addresses from this server?A . switch (config-if) #ip helper-addressB . switch (config) #ip helper-addressC . switch (config-if) #ip dhcp-addressD . switch (config-if) #ip dhcp-gatewayE...
