- All Exams Instant Download
Which attribute does a router use to select the best path when two or more different routes to the same destination exist from two different routing protocols?
Which attribute does a router use to select the best path when two or more different routes to the same destination exist from two different routing protocols?A . dual algorithmB . metricC . administrative distanceD . hop countView AnswerAnswer: C
what event has occurred if a router sends a notice level message to a syslog server?
what event has occurred if a router sends a notice level message to a syslog server?A . An interface line has changed statusB . An ICMP connection has been builtC . A certificate has expiredD . A TCP connection has been torn downView AnswerAnswer: A
R1 has learned route 10.10.10.0/24 via numerous routing protocols, which route is installed?
R1 has learned route 10.10.10.0/24 via numerous routing protocols, which route is installed?A . route with the lowest costB . route with the shortest prefix lengthC . route with the next hop that has the highest IPD . route with the lowest administrative distanceView AnswerAnswer: D
Which switch is configured correctly to meet these requirements?
Refer to the exhibit. An administrator configures four switches for local authentication using passwords that are stored as a ctyptographic hash. The four switches must also support SSH access for administrators to manage the network infrastructure. Which switch is configured correctly to meet these requirements?A . SW1B . SW2C ....
Which two command sequences must you configure on a switch to establish a Layer 3 EtherChannel with an open-standard protocol? (choose two)
Which two command sequences must you configure on a switch to establish a Layer 3 EtherChannel with an open-standard protocol? (choose two)A . interface GigabitEthernet0/0/1 Channel-group 10 mode activeB . interface GigabitEthernet0/0/1 Channel-group 10 mode autoC . interface GigabitEthernet0/0/1 Channel-group 10 mode onD . interface port-channel 10 no switchport ip...
Which action must be taken to assign a global unicast IPv6 address on an interface that is derived from the MAC address of that interface?
Which action must be taken to assign a global unicast IPv6 address on an interface that is derived from the MAC address of that interface?A . explicitly assign a link-local addressB . disable the EUI-64-bit processC . enable SLAAC on an interfaceD . configure a stateful DHCPv6 server on the...
Which two commands were used to create port channel 10?
Refer to the exhibit. Which two commands were used to create port channel 10? (choose two)A . int range g0/0-1 Channel-group 10 mode activeB . int range g0/0-1 Channel-group 10 mode desirableC . int range g0/0-1 Channel-group 10 mode passiveD . int range g0/0-1 Channel-group 10 mode autoE . int...
Which configuration accomplishes this task?
Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?A . R1# config t R1(config)# ip routing R1(config)# ip route default-route 192.168.1.1B . R1# config t R1(config)# ip routing R1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.1C . R1# config t R1(config)# ip routing...
what is the expected outcome when an EUI-64 address is generated?
what is the expected outcome when an EUI-64 address is generated?A . The seventh bit of original MAC address of the interface is invertedB . The interface ID is configured as a random 64-bit valueC . The characters FE80 are inserted at the beginning of the MAC address of the...
What two conclusions should be made about this configuration?
Refer to the exhibit. What two conclusions should be made about this configuration? (choose two)A . The root port is FastEthernet 2/1B . The spanning-tree mode is Rapid PVST+C . The designated port is FastEthernet 2/1D . The spanning-tree mode is PVST+E . This is a root bridgeView AnswerAnswer: AB
