What is the impact?

A node with Erasure Coding fails. What is the impact?A . The node stops utilizing Erasure Coding.B . Potentially increased amount of data stored in the SSD tier.C . Increased Controller VM CPU Load.D . AQS unable to do deduplication during the Erasure Coding failure.View AnswerAnswer: C

August 4, 2022No CommentsREAD MORE +

What happens to the running VMs on that node?

In a default configuration of an AHV cluster, a single node fails. What happens to the running VMs on that node?A . The cluster restarts all VMs in the event of a host failureB . The VMs do a live migration to the master node in the clusterC . The...

August 4, 2022No CommentsREAD MORE +

Where should an administrator unregister Prism Element from Prism Central?

Where should an administrator unregister Prism Element from Prism Central?A . From a Host SSH sessionB . From the Prism Central web consoleC . From the Prism Element web consoleD . From a CVM SSH sessionView AnswerAnswer: D

August 4, 2022No CommentsREAD MORE +

Where in Prism Element should the administrator change the frequency of checks and alerts?

Refer to the exhibit. System Non-Root Partition Usage shows a warning or critical alert. The administrator needs to change the frequency of checks and alerts to respond more quickly. Where in Prism Element should the administrator change the frequency of checks and alerts?A . Health Dashboard > Manage Crocks >...

August 4, 2022No CommentsREAD MORE +

Which policy should be used to meet this requirement?

Microsegmentation was recently enabled in a Nutanix environment. The administrator wants to leverage Prism Central to create a policy that will block all traffic regardless of direction, between two groups of VMs identified by their category. Which policy should be used to meet this requirement?A . An Application Security PolicyB...

August 3, 2022No CommentsREAD MORE +

What should the administrator do to correct this problem?

An administrator is configuring cross-hypervisor DR from an ESXi cluster to a new AHV cluster. When the administrator migrates a protection domain to the AHV cluster, the VMs fail to boot. What should the administrator do to correct this problem?A . Increase the snapshot frequency to more than 6 hours.B...

August 3, 2022No CommentsREAD MORE +

Which command should an administrator run from the CLI to view the uplink state of all AHV nodes in the cluster?

Which command should an administrator run from the CLI to view the uplink state of all AHV nodes in the cluster?A . allssh show_uplinksB . manage_ovs show_uplinksC . allssh manage_ovs show_uplinksD . manage ovs show uplinksView AnswerAnswer: C

August 3, 2022No CommentsREAD MORE +

What will the new values in the data resiliency dashboard be for FAILURES TOLERABLE for the Zookeeper and Extent Groups components?

Refer to Exhibit. An administrator increases the cluster RF to 3. The containers are not modified. What will the new values in the data resiliency dashboard be for FAILURES TOLERABLE for the Zookeeper and Extent Groups components?A . Zookeeper = 1 and Extent Groups = 1B . Zookeeper = 2...

August 3, 2022No CommentsREAD MORE +

What must the administrator do to meet this requirement?

An administrator is configuring data protection and DR for a multi-tier application. All VMs must be protected at the same time. What must the administrator do to meet this requirement?A . Create a consistency group for each VM with identical schedulesB . Create a consistency group for the application and...

August 3, 2022No CommentsREAD MORE +

What is the effect on live migration?

An administrator adds a node with older generation processors to an existing AHV cluster with newer generation processors . What is the effect on live migration?A . Live migration continues to function as expected and VMs can move to any AHV host.B . Live migration is prevented until the administrator...

August 3, 2022No CommentsREAD MORE +