Network Appliance NS0-176 Cisco and NetApp FlexPod Implementation and Administration Online Training
Network Appliance NS0-176 Online Training
The questions for NS0-176 were last updated at Dec 13,2025.
- Exam Code: NS0-176
- Exam Name: Cisco and NetApp FlexPod Implementation and Administration
- Certification Provider: Network Appliance
- Latest update: Dec 13,2025
Which pool of addresses is created under Servers tab in UCS Manager as part of the Service Profile creation process?
- A . WWPN Pools
- B . MAC Pools
- C . WWNN Pools
- D . UUID Suffix Pools
Your primary VSM needs to be edited, rebooted, or migrated. You need to initiate a manual switchover to your standby VSM.
What command will allow this to occur?
- A . vsm switchover
- B . System switchover
- C . Standby activate
- D . System standby
Exhibit:
Which hardware component is shown in the exhibit?
- A . GEM
- B . IOM
- C . Fl
- D . VIC
You are an administrator of a UCS system. You notice that when you apply a setting that requires a reboot, the affected hardware reboots immediately without warning. You would like to reboot to be acknowledged by an administrator instead.
What should you do to accomplish this task?
- A . Create updating templates.
- B . Create a maintenance policy.
- C . Create aa BIOS policy.
- D . Create a scrub policy.
Exhibit:
Referring to the exhibit, which two diagrams show the correct way to cable a new NetApp clustered Data ONTAP cluster with two nodes? (Choose two.)
- A . IV
- B . II
- C . I
- D . III
There are 2 chassis tied to a pair of Fabric Interconnects.
First chassis, chassis-1, has 1 link between single IOM and Fabric Module. Second chassis, chassis-4, has 4 links between single IOM and Fabric Module. Chassis discovery policy is set for 2 links.
Which statement is true?
- A . Both chassis will be added to UCS Domain utilizing all links. No additional steps needed.
- B . Both chassis will be added to UCS Domain utilizing all links only after performing chassis acknowledgment.
- C . Chassis-1 will not be added to UCS Domain. Chassis-4 will be added to UCS domain with all 4 links operating and no additional steps needed.
- D . Chassis-1 will not be added to UCS Domain. Chassis-4 will be added to UCS domain with all 4 links operating after chassis acknowledgement.
After deploying a FlexPod solution, which tool would you use to validate a successful installation?
- A . Hardware Universe
- B . Config Advisor
- C . System Manager
- D . UCS Manager
The NetApp Vistual Storage Console is used to set which three setting categories on ESXi hosts? (Choose three.)
- A . MPIO Settings
- B . Adapter Settings
- C . Logging Settings
- D . NFS Settings
- E . Security Settings
A Cisco UCS system is operating in FC End-Host Mode. The fabric Interconnects are uplinked into Nexus 5672UP switches using native FC. The service profiles are unable to boot from SAN using FC.
When executing the show flogi database command on the Nexus switches, only the Fabric Interconnect port WWNs are visible. No service profile WWNs are shown.
What caused this issue?
- A . The Nexus switches do not have NPV enabled.
- B . The Nexus must be configured for FCoE instead of native Fibre Channel.
- C . The Nexus switches do not have NPIV enabled.
- D . The zoning on the Nexus switches is incorrect.
Which FlexPod management tool allows you to manage Storage Virtual Machines (SVMs) and replication relationships?
- A . OnCommand Performance Manager
- B . OnCommand Balance
- C . OnCommand System Manager
- D . OnCommand Insight
Latest NS0-176 Dumps Valid Version with 145 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
