- All Exams Instant Download
What makes the use of the sniffer command on the FortiSwitch CLI unreliable on__port__23?
Refer to the diagnostic output: What makes the use of the sniffer command on the FortiSwitch CLI unreliable on__port__23?A . The types of packets captured is limited.B . Just the port egress payloads are printed on CLI.C . Only untagged VLAN traffic can be captured.D . The switch port might...
What are two reasons that can trigger port1 to shut down?
Refer to the exhibits. Port1 and port2 are the only ports configured with the same native VLAN 10. What are two reasons that can trigger port1 to shut down? (Choose two.)A . port1 was shut down by loop guard protection.B . STP triggered a loop and applied loop guard protection...
Which MAC address is shown in the above output?
Refer to the diagnostic output: Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?A . It is a MAC address of FortiLink interface on FortiGate.B . It is a MAC address of...
How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?
How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?A . FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces.B . FortiGate configures FortiSwitch to perform ingress sampling on all switch...
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?A . All ports have auto-discovery enabled by default.B . No ports are enabled by default for auto-discovery. This must be configured under config switch interface.C . The ports...
Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?
Refer to the exhibit. The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports, and these ports are connected to endpoints which are powered by PoE. Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and...
What two conclusions can be made regarding DHCP snooping configuration?
Refer to the exhibit. What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)A . Maximum value to accept clients DHCP request is configured as per DHCP server range.B . FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.C . DHCP clients that are trusted by...
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)A . Detected management interfacesB . Loopback interfacesC . Switch virtual interfacesD . Physical interfacesView AnswerAnswer: B, C
What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?
What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?A . FortiGate multi-tenancyB . Multi-chassis link aggregation trunkC . FortiGate clustering protocolD . FortiLink split interfaceView AnswerAnswer: A
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1?
Refer to the exhibits Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch. Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose...
