DELL EMC DES-4122 Specialist - Implementation Engineer PowerEdge Version 2.0 Online Training

In the preparation of DES-4122 Specialist – Implementation Engineer PowerEdge Version 2.0, the quality of DELL EMC DES-4122 Specialist – Implementation Engineer PowerEdge Version 2.0 Online Training is visible through the elements of knowledge and skill practice in a small span of time. Exam4Training also provides 100% money back guarantee to the customers who took the DELL EMC DES-4122 exam. The DCS-IE DES-4122 is available for practicing the questions and getting full benefits.

Page 1 of 4

1. A technician is creating a virtual disk in the iDRAC (2x 4 TB NL-SAS in RAID 1) to install Windows 2016 They manually boot to the OS installation media without using the Lifecycle Controller OS Deployment wizard Only the first 2048 GB on the virtual disk can be partitioned

How should the technician obtain access to the remaining 2 TB (approximately) of storage?

Use the Lifecycle Controller OS Deployment Wizard to deploy the OS on this server

Delete the 4 TB virtual disk and create a virtual (boot) disk no larger than 2048 GB

Upgrade to a newer version of the operating system

Use F2 to go into the BIOS, change the BIOS boot mode to UEFI, and try again

2. Where is the data stored to allow Easy Restore to successfully complete a system board replacement?

NAND Flash module on the disk drive mid plane

IDSDM SD card

vFlash SD card

Serial Flash storage in the server's front panel

3. A technician needs to repurpose a Dell EMC PowerEdge server. The server has dual processors with 18 cores each The OS only "sees" 24 threads in total.

Which setting should the technician change in Processor Settings in the System BIOS?

System Profile

Virtualization Technology

HyperThreading

Number of Cores per Processor

4. What are the default settings used when applying firmware and a configuration to a replaced part using the Lifecycle Controller?

Firmware: Upgrade to latest available version Configuration Apply always

Firmware Allow version upgrade only Configuration: Disabled

Firmware: Match firmware of replaced part Configuration Apply always

Firmware Disabled Configuration Apply only if firmware match

5. What is the purpose of the Silicon-Based Hardware Root of Trust feature in Dell EMC PowerEdge 14G servers?

Ensures that the installed operating system is authentic

Ensures that the server has a valid Service Tag number

Ensures that no unauthorized BIOS or firmware codes are run

Ensures that the server boots only when connected to a verified network

6. DRAG DROP

Match each status LED indicator on the Dell EMC 14G PowerEdge server with its corresponding condition.

7. An engineer is checking a newly delivered Dell EMC PowerEdge R640 server that will be deployed for a new database environment.

The inventory consists of:

The server power configuration will be set for gnd redundancy. The management switch is 1000 Base-T and the top of rack switches 10Gb

What additional component(s) is needed for this configuration?

Hot-plug power supply, 750 W - qty 1

Hot-plug power supply, 1100W - qty 1

Dell Networking, cable, 40GbE (QSFP+) to 4 x 10GbE SFP+ passive copper breakout cable, 3 meters - qty 2

C20 to C21, PDU style, 250 V, 16 Amp, 3 5 meters power cord - qty 2

8. What is a systems management console solution optimized for monitoring and managing Dell enterprise and remote office hardware?

SupportAssist Enterprise

iSM

OpenManage Essentials

iDRAC9

9. DRAG DROP

Refer to the exhibit.

Match each callout to the Dell EMC PowerEdge server model shown.

10. After completing a disk rebuild operation, a technician needs to configure the system so that the rebuild process happens faster the expense of slowing users down.

Which setting should be changed?

Rebuild Rate in the BIOS settings

System Profile to Performance in the BIOS settings

System Profile to Performance in the iDRAC GUI

Rebuild Rate in the iDRAC GUI

Page 2 of 4

11. An engineer wants to fully leverage Microsoft Windows Server 2016 for TPM-based guarded host deployment of a 14G server.

Which BIOS settings need to be used for installing the Windows server?

A)

Option A

Option B

Option C

Option D

12. A company that has very specific firmware requirements has acquired Dell EMC PowerEdge servers Any replaced parts of the type must match the original parts identically. The procedure must be as simple as possible with minimal risk.

What action should a technician take to help accomplish this goal?

Configure servers to access the remote firmware repository

Enable the Match Firmware of Replaced Part setting in the system BIOS

Install and configure a repository manager

Enable the Collect System Inventory On Restart (CSIOR) attribute

13. DRAG DROP

Match each RAID level to its characteristic.

14. A technician installs eight servers into a fully operational rack with top of rack switch Each server has a quad 1Gb NIC and redundant power supplies. The company uses iDRAC in shared LOM mode with LOM1 as the selected NIC

What should the technician do to verify iDRAC connectivity on each server?

iDRAC Datacenter license is installed.

Ethernet port LOM1 is cabled and the link light is green.

iDRAC dedicated NIC port is cabled and the link light is green

iDRAC Enterprise license is installed

15. Dell EMC PowerEdge 14G servers support which technology?

Quicksync 1.0

Intel Boot Guard

AMD GuardMI

iDRAC8

16. Which type of access is known as Firmware RACADM on a Dell EMC PowerEdge server?

Accessing RACADM running the Dell Toolkit

Accessing RACADM with OpenManage software

Logging into iDRAC using SSH or Telnet

Logging into iDRAC through Boot Manager

17. A Dell EMC PowerEdge 14G server uses Intel OPTANE DC Persistent Memory in App Direct mode .

What is the minimum size DIMM supported for this type of memory?

64 GB

128 GB

256 GB

512 GB

18. A technician needs to change the iDRAC password on a Dell EMC PowerEdge 14G server in a lights-out datacenter. The be rebooted because it is in production. The iDRAC is configured with the default credentials

How could the technician change the iDRAC password?

SupportAssist Enterprise

iDRAC Web GUI

OpenManage Server Administrator

Virtual Console; press F2 after rebooting system

19. What is a characteristic of SupportAssist Enterprise on Dell EMC PowerEdge 14G servers?

Used for customers that want monitoring of fewer than 1,000 server, storage, and networking devices

Dispatches technical support from Dell for all Dell servers, storage, and networking devices

Proactive, predictive, and automated support technology to enable faster resolution and reporting

Includes onsite monitoring and automated collection of system state information

20. DRAG DROP

What is the correct order of steps taken during the BIOS/UEFI Recovery process?

Page 3 of 4

21. A technician is creating a virtual disk in the iDRAC (2x 4 TB NL-SAS in RAID 1) to install Windows 2016 They manually boot to the OS installation media without using the Lifecycle Controller OS Deployment wizard Only the first 2048 GB on the virtual disk can be partitioned

How should the technician obtain access to the remaining 2 TB (approximately) of storage?

Use the Lifecycle Controller OS Deployment Wizard to deploy the OS on this server

Delete the 4 TB virtual disk and create a virtual (boot) disk no larger than 2048 GB

Upgrade to a newer version of the operating system

Use F2 to go into the BIOS, change the BIOS boot mode to UEFI, and try again

22. Where is the data stored to allow Easy Restore to successfully complete a system board replacement?

NAND Flash module on the disk drive mid plane

IDSDM SD card

vFlash SD card

Serial Flash storage in the server's front panel

23. A technician needs to repurpose a Dell EMC PowerEdge server. The server has dual processors with 18 cores each The OS only "sees" 24 threads in total.

Which setting should the technician change in Processor Settings in the System BIOS?

System Profile

Virtualization Technology

HyperThreading

Number of Cores per Processor

24. What are the default settings used when applying firmware and a configuration to a replaced part using the Lifecycle Controller?

Firmware: Upgrade to latest available version Configuration Apply always

Firmware Allow version upgrade only Configuration: Disabled

Firmware: Match firmware of replaced part Configuration Apply always

Firmware Disabled Configuration Apply only if firmware match

25. What is the purpose of the Silicon-Based Hardware Root of Trust feature in Dell EMC PowerEdge 14G servers?

Ensures that the installed operating system is authentic

Ensures that the server has a valid Service Tag number

Ensures that no unauthorized BIOS or firmware codes are run

Ensures that the server boots only when connected to a verified network

26. DRAG DROP

Match each status LED indicator on the Dell EMC 14G PowerEdge server with its corresponding condition.

27. An engineer is checking a newly delivered Dell EMC PowerEdge R640 server that will be deployed for a new database environment.

The inventory consists of:

The server power configuration will be set for gnd redundancy. The management switch is 1000 Base-T and the top of rack switches 10Gb

What additional component(s) is needed for this configuration?

Hot-plug power supply, 750 W - qty 1

Hot-plug power supply, 1100W - qty 1

Dell Networking, cable, 40GbE (QSFP+) to 4 x 10GbE SFP+ passive copper breakout cable, 3 meters - qty 2

C20 to C21, PDU style, 250 V, 16 Amp, 3 5 meters power cord - qty 2

28. What is a systems management console solution optimized for monitoring and managing Dell enterprise and remote office hardware?

SupportAssist Enterprise

iSM

OpenManage Essentials

iDRAC9

29. DRAG DROP

Refer to the exhibit.

Match each callout to the Dell EMC PowerEdge server model shown.

30. After completing a disk rebuild operation, a technician needs to configure the system so that the rebuild process happens faster the expense of slowing users down.

Which setting should be changed?

Rebuild Rate in the BIOS settings

System Profile to Performance in the BIOS settings

System Profile to Performance in the iDRAC GUI

Rebuild Rate in the iDRAC GUI

Page 4 of 4

31. An engineer wants to fully leverage Microsoft Windows Server 2016 for TPM-based guarded host deployment of a 14G server.

Which BIOS settings need to be used for installing the Windows server?

A)

Option A

Option B

Option C

Option D

32. A company that has very specific firmware requirements has acquired Dell EMC PowerEdge servers Any replaced parts of the type must match the original parts identically. The procedure must be as simple as possible with minimal risk.

What action should a technician take to help accomplish this goal?

Configure servers to access the remote firmware repository

Enable the Match Firmware of Replaced Part setting in the system BIOS

Install and configure a repository manager

Enable the Collect System Inventory On Restart (CSIOR) attribute

33. DRAG DROP

Match each RAID level to its characteristic.

34. A technician installs eight servers into a fully operational rack with top of rack switch Each server has a quad 1Gb NIC and redundant power supplies. The company uses iDRAC in shared LOM mode with LOM1 as the selected NIC

What should the technician do to verify iDRAC connectivity on each server?

iDRAC Datacenter license is installed.

Ethernet port LOM1 is cabled and the link light is green.

iDRAC dedicated NIC port is cabled and the link light is green

iDRAC Enterprise license is installed

35. Dell EMC PowerEdge 14G servers support which technology?

Quicksync 1.0

Intel Boot Guard

AMD GuardMI

iDRAC8

36. Which type of access is known as Firmware RACADM on a Dell EMC PowerEdge server?

Accessing RACADM running the Dell Toolkit

Accessing RACADM with OpenManage software

Logging into iDRAC using SSH or Telnet

Logging into iDRAC through Boot Manager

37. A Dell EMC PowerEdge 14G server uses Intel OPTANE DC Persistent Memory in App Direct mode .

What is the minimum size DIMM supported for this type of memory?

64 GB

128 GB

256 GB

512 GB

38. A technician needs to change the iDRAC password on a Dell EMC PowerEdge 14G server in a lights-out datacenter. The be rebooted because it is in production. The iDRAC is configured with the default credentials

How could the technician change the iDRAC password?

SupportAssist Enterprise

iDRAC Web GUI

OpenManage Server Administrator

Virtual Console; press F2 after rebooting system

39. What is a characteristic of SupportAssist Enterprise on Dell EMC PowerEdge 14G servers?

Used for customers that want monitoring of fewer than 1,000 server, storage, and networking devices

Dispatches technical support from Dell for all Dell servers, storage, and networking devices

Proactive, predictive, and automated support technology to enable faster resolution and reporting

Includes onsite monitoring and automated collection of system state information

40. DRAG DROP

What is the correct order of steps taken during the BIOS/UEFI Recovery process?

Latest DES-4122 Dumps Valid Version with 60 Q&As

Latest And Valid Q&A | Instant Download | Once Fail, Full Refund

Instant Download DES-4122 PDF