- All Exams Instant Download
Which action must be taken to assign a global unicast IPv6 address on an interface that is derived from the MAC address of that interface?
Which action must be taken to assign a global unicast IPv6 address on an interface that is derived from the MAC address of that interface?A . explicitly assign a link-local addressB . disable the EUI-64-bit processC . enable SLAAC on an interfaceD . configure a stateful DHCPv6 server on the...
Which two commands were used to create port channel 10?
Refer to the exhibit. Which two commands were used to create port channel 10? (choose two)A . int range g0/0-1 Channel-group 10 mode activeB . int range g0/0-1 Channel-group 10 mode desirableC . int range g0/0-1 Channel-group 10 mode passiveD . int range g0/0-1 Channel-group 10 mode autoE . int...
Which configuration accomplishes this task?
Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?A . R1# config t R1(config)# ip routing R1(config)# ip route default-route 192.168.1.1B . R1# config t R1(config)# ip routing R1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.1C . R1# config t R1(config)# ip routing...
what is the expected outcome when an EUI-64 address is generated?
what is the expected outcome when an EUI-64 address is generated?A . The seventh bit of original MAC address of the interface is invertedB . The interface ID is configured as a random 64-bit valueC . The characters FE80 are inserted at the beginning of the MAC address of the...
What two conclusions should be made about this configuration?
Refer to the exhibit. What two conclusions should be made about this configuration? (choose two)A . The root port is FastEthernet 2/1B . The spanning-tree mode is Rapid PVST+C . The designated port is FastEthernet 2/1D . The spanning-tree mode is PVST+E . This is a root bridgeView AnswerAnswer: AB
Which command is used to specify the delay time in seconds for LLDP to initialize on any interface?
Which command is used to specify the delay time in seconds for LLDP to initialize on any interface?A . lldp timerB . lldp holdtimeC . lldp reinitD . lldp tlv-selectView AnswerAnswer: C Explanation: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/12-2_37_ey/configuration/guide/scg/swlldp.pdf
What is a characteristic of spine-and-leaf architecture?
What is a characteristic of spine-and-leaf architecture?A . It provides variable latency.B . Each link between leaf switches allows for higher bandwidth.C . Each device is separated by the same number of hops.D . It provides greater predictability on STP blocked ports.View AnswerAnswer: C
Which route characteristic is used by the router to forward the packet that receives for destination IP 172.16.32.1?
Refer to the exhibit. Router R1 is running three different routing protocols. Which route characteristic is used by the router to forward the packet that receives for destination IP 172.16.32.1?A . metricB . longest prefixC . costD . administrative distanceView AnswerAnswer: B
Which statement explains the configuration error message that is received?
Refer to the exhibit. Which statement explains the configuration error message that is received?A . it belongs to a private IP address rangeB . the router dose not support /28 maskC . it is a network IP addressD . it is a broadcast IP addressView AnswerAnswer: D
What is the default behavior of a layer 2 switch when a frame with an unknown destination MAC address is received?
What is the default behavior of a layer 2 switch when a frame with an unknown destination MAC address is received?A . The Layer 2 switch forwards the packet and adds the destination MAC address to its MAC address tableB . The Layer 2 switch sends a copy of a...
