- All Exams Instant Download
Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20.0/26 from the 10.0.10.0/26 subnet while still allowing all other traffic?
Refer to the exhibit. An extended ACL has been configured and applied to router R2. The configuration started to work as intended. Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20.0/26 from the 10.0.10.0/26 subnet while still allowing all other traffic? (Choose two)A . Add...
Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another?
Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another? (Choose two)A . Configure the ipv6 route 2012::/126 2023::1...
If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10 . 13.0.1 120 command, how does the router respond?
Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10 . 13.0.1 120 command, how does the router respond?A . It ignores the new static route until the existing OSPF default route is removedB . It immediately replaces the existing...
Which two interface counters are incremented?
A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented? (Choose two)A . runtsB . giantsC . frameD . CRCE . input errorsView AnswerAnswer: D E Explanation: Whenever the physical transmission has problems, the receiving device might receive a frame whose bits have...
Which type of route does R1 use to reach host 10.10.13.10/32?
Refer to the exhibit. Which type of route does R1 use to reach host 10.10.13.10/32?A . floating static routeB . host routeC . default routeD . network routeView AnswerAnswer: D Explanation: From the output, we see R1 will use the entry “O 10.10.13.0/25 *110/4576+ via 10.10.10.1, …” to reach host...
Which IP address is the source IP?
Refer to the exhibit. An engineer configured NAT translations and has verified that the configuration is correct. Which IP address is the source IP?A . 10.4.4.4B . 10.4.4.5C . 172.23.103.10D . 172.23.104.4View AnswerAnswer: D
Which two commands must be configured on the New York router so that it can reach the Lo1 interface of the Atlanta router via Washington when the link between New York and Atlanta goes down?
Refer to Exhibit. An engineer is configuring the NEW York router to reach the Lo1 interface of the Atlanta router using interface Se0/0/0 as the primary path. Which two commands must be configured on the New York router so that it can reach the Lo1 interface of the Atlanta router...
Which two values or settings must be entered when configuring a new WLAN in the Cisco Wireless LAN Controller GUI? (Choose two)
Which two values or settings must be entered when configuring a new WLAN in the Cisco Wireless LAN Controller GUI? (Choose two)A . management interface settingsB . QoS settingsC . Ip address of one or more access pointsD . SSIDE . Profile nameView AnswerAnswer: D E
Which state verifies the designated router is in the proper mode?
An engineer configured an OSPF neighbor as a designated router. Which state verifies the designated router is in the proper mode?A . ExchangeB . 2-wayC . FullD . InitView AnswerAnswer: C
Which protocol allows the engineer to perform this function using the Cisco IOS MIB?
A network engineer must back up 20 network router configurations globally within a customer environment. Which protocol allows the engineer to perform this function using the Cisco IOS MIB?A . CDPB . SNMPC . SMTPD . ARPView AnswerAnswer: B Explanation: SNMP is an application-layer protocol that provides a message format...
