- All Exams Instant Download
What does router R1 use as its OSPF router-ID?
Refer to the exhibit. What does router R1 use as its OSPF router-ID?A . 10.10.1.10B . 10.10.10.20C . 172.16.15.10D . 192.168.0.1View AnswerAnswer: C Explanation: OSPF uses the following criteria to select the router ID:
Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another?
Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another? (Choose two.)A . Configure the ipv6 route 2012::/126 2023::1...
When configuring IPv6 on an interface, which two IPv6 multicast groups are joined? (Choose two)
When configuring IPv6 on an interface, which two IPv6 multicast groups are joined? (Choose two)A . 2000::/3B . 2002::5C . FC00::/7D . FF02::1E . FF02::2View AnswerAnswer: DE Explanation: When an interface is configured with IPv6 address, it automatically joins the all nodes (FF02::1) and solicited-node (FF02::1:FFxx:xxxx) multicast groups. The all-node...
How is OSPF configured?
Refer to the exhibit. The show ip ospf interface command has been executed on R1. How is OSPF configured?A . The interface is not participating in OSPC . A point-to-point network type is configured.D . The default Hello and Dead timers are in use.E . There are six OSPF neighbors...
Which set of action satisfy the requirement for multi-factor authentication?
Which set of action satisfy the requirement for multi-factor authentication?A . The user swipes a key fob, then clicks through an email link.B . The user enters a user name and password, and then clicks a notification in an authentication app on a mobile device.C . The user enters a...
Which two actions influence the EIGRP route selection process? (Choose two)
Which two actions influence the EIGRP route selection process? (Choose two) A. The router calculates the reported distance by multiplying the delay on the exiting Interface by 256. B. The router calculates the best backup path to the destination route and assigns it as the feasible successor. C. The router...
A user configured OSPF and advertised the Gigabit Ethernet interface in OSPF by default, which type of OSPF network does this interface belong to?
A user configured OSPF and advertised the Gigabit Ethernet interface in OSPF by default, which type of OSPF network does this interface belong to?A . point-to-multipointB . point-to-pointC . broadcastD . nonbroadcastView AnswerAnswer: C Explanation: The Broadcast network type is the default for an OSPF enabled ethernet interface (while Point-toPoint...
What does router R1 use as its OSPF router-ID?
Refer to the exhibit. What does router R1 use as its OSPF router-ID?A . 10.10.1.10B . 10.10.10.20C . 172.16.15.10D . 192.168.0.1View AnswerAnswer: C Explanation: OSPF uses the following criteria to select the router ID:
What is the effect of this configuration?
Refer to the exhibit. What is the effect of this configuration?A . The switch port interface trust state becomes untrusted.B . The switch port remains administratively down until the interface is connected to another switch.C . Dynamic ARP inspection is disabled because the ARP ACL is missing.D . The switch...
Which usable IP address and subnet mask combination meets this criteria?
An engineer must configure a /30 subnet between two routers. Which usable IP address and subnet mask combination meets this criteria?A . interface e0/0 description to HQ-A370:98968 ip address 10.2.1.3 255.255.255.252B . interface e0/0 description to HQ-A370:98968 ip address 192.168.1.1 255.255.255.248C . interface e0/0 description to HQ-A370:98968 ip address 172.16.1.4...
