Cisco 350-401 Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) Online Training
Cisco 350-401 Online Training
The questions for 350-401 were last updated at Sep 14,2025.
- Exam Code: 350-401
- Exam Name: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)
- Certification Provider: Cisco
- Latest update: Sep 14,2025
Refer to the Exhibit.
Rapid PVST+ is enabled on all switches.
Which command set must be configured on switch1 to achieve the following results on port fa0/1?
✑ When a device is connected, the port transitions immediately to a forwarding state.
✑ The interface should not send or receive BPDUs.
✑ If a BPDU is received, it continues operating normally.
- A . Switch1(config)# spanning-tree portfast bpdufilter default
Switch1(config)# interface f0/1
Switch1(config-if)# spanning-tree portfast - B . Switch1(config)# spanning-tree portfast bpduguard default
Switch 1 (config)# interface f0/1
Switch1 (config-if)# spanning-tree portfast - C . Switch1(config)# interface f0/1
Switch1(config-if)# spanning-tree portfast - D . Switch1(config)# interface f0/1
Switch1(config-if)# spanning-tree portfast
Switch1 (config-if)# spanning-tree bpduguard enable
Refer to the exhibit.
What is the Json syntax that is formed from the data?
- A . {Name: Bob Johnson, Age: 75, Alive: true, Favorite Foods: [Cereal, Mustard, Onions]}
- B . {"Name": "Bob Johnson", "Age": 75, "Alive": true, "Favorite Foods": ["Cereal", "Mustard", "Onions"]}
- C . {"˜Name’: "˜Bob Johnson’, "˜Age’: 75, "˜Alive’: True, "˜Favorite Foods’: "˜Cereal’, "˜Mustard’, "˜Onions’}
- D . {"Name": "Bob Johnson", "Age": Seventyfive, "Alive": true, "Favorite Foods": ["Cereal", "Mustard", "Onions"]}
In a wireless Cisco SD-Access deployment, which roaming method is used when a user moves from one access point to another on a different access switch using a single WLC?
- A . Layer 3
- B . inter-xTR
- C . auto anchor
- D . fast roam
Refer to the exhibit.
Which type of antenna is show on the radiation patterns?
- A . Dipole
- B . Yagi
- C . Patch
- D . Omnidirectional
DRAG DROP
Drag and drop the characteristics from the left onto the orchestration tools they describe on the right.
Which command set configures RSPAN to capture outgoing traffic from VLAN 3 on interface GigabitEthernet 0/3 while ignoring other VLAN traffic on the same interface?
- A . monitor session 2 source interface gigabitethernet0/3 tx
monitor session 2 filter vlan 3 - B . monitor session 2 source interface gigabitethernet0/3 tx
monitor session 2 filter vlan 1- 2, 4 – 4094 - C . monitor session 2 source interface gigabitethernet0/3 rx
monitor session 2 filter vlan 3 - D . monitor session 2 source interface gigabitethernet0/3 rx
monitor session 2 filter vlan 1 – 2, 4 – 4094
What is a fact about Cisco EAP-FAST?
- A . It does not require a RADIUS server certificate.
- B . It requires a client certificate.
- C . It is an IETF standard.
- D . It operates in transparent mode.
What is the data policy in a Cisco SD-WAN deployment?
- A . list of ordered statements that define node configurations and authentication used within the SD-WAN overlay
- B . Set of statements that defines how data is forwarded based on IP packet information and specific VPNs
- C . detailed database mapping several kinds of addresses with their corresponding location
- D . group of services tested to guarantee devices and links liveliness within the SD-WAN overlay
Refer to the Exhibit.
What is the effect of this configuration?
- A . When users attempt to connect to vty lines 0 through 4, the device will authenticate them against TACACS+ if local authentication fails
- B . The device will authenticate all users connecting to vty lines 0 through 4 against TACACS+
- C . The device will allow users at 192.168.0.202 to connect to vty lines 0 through 4 using the password ciscotestkey
- D . The device will allow only users at 192.166.0.202 to connect to vty lines 0 through 4
DRAG DROP
Refer to the exhibit
Drag and drop the snippets into the RESTCONF request to form the request that returns this response Not all options are used
Latest 350-401 Dumps Valid Version with 404 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
Question 91 has a wrong answer marked s correct. The answer is B.
BPDU filter is the only option to block BPDUs while not going inte err disabled when a BPDU is received.
https://www.exam4training.com/which-command-set-must-be-configured-on-switch1-to-achieve-the-following-results-on-port-fa0-1/
https://www.cisco.com/en/US/docs/switches/metro/me3600x_3800x/trash/swstpopt.html#:~:text=The%20BPDU%20filtering%20feature%20can,bpdufilter%20default%20global%20configuration%20command.