Cisco 350-401 Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) Online Training
Cisco 350-401 Online Training
The questions for 350-401 were last updated at Nov 03,2025.
- Exam Code: 350-401
- Exam Name: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)
- Certification Provider: Cisco
- Latest update: Nov 03,2025
Refer to the Exhibit.
Which command is required to verify NETCONF capability reply messages?
- A . show netconf | section rpc-reply
- B . show netconf rpc-reply
- C . show netconf xml rpc-reply
- D . show netconf schema | section rpc-reply
A network engineer must configure a router to send logging messages to a syslog server based on these requirements:
– uses syslog IP address: 10.10.10.1
– uses a reliable protocol
– must not use any well-known TCP/UDP ports.
Which configuration must be used?
- A . logging host 10.10.10.1 transport tcp port 1024
- B . logging origin-id 10.10.10.1
- C . logging host 10.10.10.1 transport udp port 1023
- D . logging host 10.10.10.1 transport udp port 1024
Refer to the Exhibit.
A network engineer must configure NETCONF. After creating the configuration, the engineer gets output from the command show line, but not from show running-config.
Which command completes the configuration?
- A . Option A
- B . Option B
- C . Option C
- D . Option D
An engineer is configuring a new SSID to present users with a splash page for authentication.
Which WLAN Layer 3 setting must be configured to provide this functionally?
- A . CCKM
- B . WPA2 Policy
- C . Local Policy
- D . Web Policy
An engineer must create an EEM script to enable OSPF debugging in the event the OSPF neighborship goes down.
Which script must the engineer apply?
- A . Option A
- B . Option B
- C . Option C
- D . Option D
DRAG DROP
An engineer is working with the Cisco DNA Center API Drag and drop the methods from the left onto the actions that they are used for on the right.
Refer to the Exhibit.
Router BRDR-1 is configured to receive the 0.0.0.0/0 and 172.17.1.0/24 network via BGP and advertise them into OSPF are 0. An engineer has noticed that the OSPF domain is receiving only the 172.17.1.0/24 route and default route 0.0.0.0/0 is still missing.
Which configurating must engineer apply to resolve the problem?
- A . Option A
- B . Option B
- C . Option C
- D . Option D
AN engineer is implementing a route map to support redistribution within BGP. The route map must configured to permit all unmatched routes.
Which action must the engineer perform to complete this task?
- A . Include a permit statement as the first entry
- B . Include at least one explicit deny statement
- C . Remove the implicit deny entry
- D . Include a permit statement as the last entry
Refer to the Exhibit.
A network operator is attempting to configure an IS-IS adjacency between two routers, but the adjacency cannot be established. To troubleshoot the problem, the operator collects this debugging output.
Which interfaces are misconfigured on these routers?
- A . The peer router interface is configured as Level 1 only, and the R2 interface is configured as Level 2 only
- B . The R2 interface is configured as Level 1 only, and the Peer router interface is configured as Level 2
only - C . The R2 interface is configured as point-to-point, and the peer router interface is configured as multipoint.
- D . The peer router interface is configured as point-as-point, and the R2 interface is configured as multipoint.
AN engineer is implementing MPLS OAM to monitor traffic within the MPLS domain.
Which action must the engineer perform to prevent from being forwarded beyond the service provider domain when the LSP is down?
- A . Disable IP redirects only on outbound interfaces
- B . Implement the destination address for the LSP echo request packet in the 127.x.y.z/8 network
- C . Disable IP redirects on all ingress interfaces
- D . Configure a private IP address as the destination address of the headend router of Cisco MPLS TE.
Latest 350-401 Dumps Valid Version with 404 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
Question 91 has a wrong answer marked s correct. The answer is B.
BPDU filter is the only option to block BPDUs while not going inte err disabled when a BPDU is received.
https://www.exam4training.com/which-command-set-must-be-configured-on-switch1-to-achieve-the-following-results-on-port-fa0-1/
https://www.cisco.com/en/US/docs/switches/metro/me3600x_3800x/trash/swstpopt.html#:~:text=The%20BPDU%20filtering%20feature%20can,bpdufilter%20default%20global%20configuration%20command.