Cisco 300-710 Securing Networks with Cisco Firepower (SNCF) Online Training
Cisco 300-710 Online Training
The questions for 300-710 were last updated at Oct 14,2025.
- Exam Code: 300-710
- Exam Name: Securing Networks with Cisco Firepower (SNCF)
- Certification Provider: Cisco
- Latest update: Oct 14,2025
Which two dynamic routing protocols are supported in Firepower Threat Defense without using FlexConfig? (Choose two.)
- A . EIGRP
- B . OSPF
- C . static routing
- D . IS-IS
- E . BGP
Which policy rule is included in the deployment of a local DMZ during the initial deployment of a Cisco NGFW through the Cisco FMC GUI?
- A . a default DMZ policy for which only a user can change the IP addresses.
- B . deny ip any
- C . no policy rule is included
- D . permit ip any
What are two application layer preprocessors? (Choose two.)
- A . CIFS
- B . IMAP
- C . SSL
- D . DNP3
- E . ICMP
An engineer is tasked with deploying an internal perimeter firewall that will support multiple DMZs
Each DMZ has a unique private IP subnet range.
How is this requirement satisfied?
- A . Deploy the firewall in transparent mode with access control policies.
- B . Deploy the firewall in routed mode with access control policies.
- C . Deploy the firewall in routed mode with NAT configured.
- D . Deploy the firewall in transparent mode with NAT configured.
An engineer must configure high availability for the Cisco Firepower devices. The current network topology does not allow for two devices to pass traffic concurrently.
How must the devices be implemented in this environment?
- A . in active/active mode
- B . in a cluster span EtherChannel
- C . in active/passive mode
- D . in cluster interface mode
When deploying a Cisco ASA Firepower module, an organization wants to evaluate the contents of the traffic without affecting the network. It is currently configured to have more than one instance of the same device on the physical appliance.
Which deployment mode meets the needs of the organization?
- A . inline tap monitor-only mode
- B . passive monitor-only mode
- C . passive tap monitor-only mode
- D . inline mode
An organization has a Cisco FTD that uses bridge groups to pass traffic from the inside interfaces to the outside interfaces. They are unable to gather information about neighbouring Cisco devices or use multicast in their environment.
What must be done to resolve this issue?
- A . Create a firewall rule to allow CDP traffic.
- B . Create a bridge group with the firewall interfaces.
- C . Change the firewall mode to transparent.
- D . Change the firewall mode to routed.
A network engineer implements a new Cisco Firepower device on the network to take advantage of its intrusion detection functionality. There is a requirement to analyze the traffic going across the device, alert on any malicious traffic, and appear as a bump in the wire.
How should this be implemented?
- A . Specify the BVl IP address as the default gateway for connected devices.
- B . Enable routing on the Cisco Firepower
- C . Add an IP address to the physical Cisco Firepower interfaces.
- D . Configure a bridge group in transparent mode.
Which two conditions must be met to enable high availability between two Cisco FTD devices? (Choose two.)
- A . same flash memory size
- B . same NTP configuration
- C . same DHCP/PPoE configuration
- D . same host name
- E . same number of interfaces
An engineer is building a new access control policy using Cisco FMC. The policy must inspect a unique IPS policy as well as log rule matching.
Which action must be taken to meet these requirements?
- A . Configure an IPS policy and enable per-rule logging.
- B . Disable the default IPS policy and enable global logging.
- C . Configure an IPS policy and enable global logging.
- D . Disable the default IPS policy and enable per-rule logging.
Latest 300-710 Dumps Valid Version with 153 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
