Cisco 300-515 Implementing Cisco Service Provider VPN Services (SVPI) Online Training
Cisco 300-515 Online Training
The questions for 300-515 were last updated at Oct 23,2025.
- Exam Code: 300-515
- Exam Name: Implementing Cisco Service Provider VPN Services (SVPI)
- Certification Provider: Cisco
- Latest update: Oct 23,2025
Which two are characteristics of using a non-MPLS peer-to-peer model over a traditional overlay model? (Choose two.)
- A . The model is suited for nonredundant configurations.
- B . The configuration on a newly added site PE is updated automatically.
- C . Provider routers know the customer network topology.
- D . The customer specifies the exact site-to-site traffic profile.
- E . Routing information is exchanged between the customer router and one or a few PEs.
What is the primary function of a VRF on a router?
- A . It enables the router to support multiple separate routing tables, which allows the device to handle overlapping IP addresses.
- B . It enables a router to run BGP and a distance vector routing protocol at the same time,
which allows it to serve as a VPN endpoint between remote sites. - C . It enables a router to configure VLANs locally, which provides segregation between networks.
- D . It enables the router to provide faster switching through the network by using labels to identify the input and output interfaces for neighbor routers.
Refer to the exhibit.
Which statement about this output is true?
- A . The router IP 192.168.1.2 sent an implicit null, and the output is from the penultimate LSR.
- B . The adjacent router is the egress LSR and has mpls ldp explicit-null configured.
- C . The adjacent LSR router configured mpls label range 0.
- D . The zero in the second column is the normal behavior of an egress router LSR.
Refer to the exhibit.
A network engineer has been called to configure the four PE devices in order to enable full communication among the four CE devices connected to them. While starting to configure, he experienced a connectivity issue .
Which two tasks should the engineer perform in order to begin the process correctly? (Choose two.)
- A . Configure PE3 to export route-targets 100:1 and 200:2.
- B . Configure PE3 to import route-targets 100:1 and 200:2.
- C . Configure PE4 to import route-targets 101:1 and 202:2.
- D . Configure PE2 to export route-targets 300:3 and 400:4.
- E . Configure PE1 to import route-targets 300:3 and 400:4.
Refer to the exhibit.
A network operator is implementing EVPN IRB on PE1 .
Which two command placements enable the advertisement of Type 2 routes and what information do Type 2 routes contain? (Choose two.)
- A . The operator adds in “host-routing” under the VRF EVPN.
- B . Type 2 routes contain MAC/IP information.
- C . Type 2 routes contain Ethernet Auto-Discovery information.
- D . The operator adds in “host-routing” under the BVI651 interface.
- E . Type 2 routes contain inclusive source-specific multicast route information.
Refer to the exhibit.
An engineer is implementing an MPLS P2MP TE solution .
Which type of router can serve as the midpoint router and the tailend router in this P2MP TE network implementation?
- A . headend
- B . source
- C . transit
- D . bud
In an Ethernet Virtual Circuit environment, which restriction do bridge domains have when STP is running?
- A . The STP mode must be RSTP or PVST+
- B . Bridge domains must be mapped to a different VLAN.
- C . The STP mode must be MSTP
- D . Bridge domains must belong to different MST instances.
In a typical service provider environment, which two tools are used to help scale PE router connectivity requirements? (Choose two.)
- A . route reflectors
- B . VPNv4 address family
- C . originator ID
- D . cluster ID
- E . confederations
You are troubleshooting ARP connectivity issues for an Ethernet interface on an IOS XR network that runs IS- IS. You verify that the IGP protocol is running, but an ARP entry has not yet been created.
Which action should you take?
- A . debug ping packets
- B . debug ARP
- C . ping the connected neighbor
- D . verify the RIB table routes
Which utility can you use to validate an LSP in an MPLS environment?
- A . uRPF
- B . MPLS LSP ping
- C . logging
- D . RSVP
Latest 300-515 Dumps Valid Version with 59 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
