Cisco 350-601 Implementing and Operating Cisco Data Center Core Technologies (DCCOR) Online Training
Cisco 350-601 Online Training
The questions for 350-601 were last updated at Sep 14,2025.
- Exam Code: 350-601
- Exam Name: Implementing and Operating Cisco Data Center Core Technologies (DCCOR)
- Certification Provider: Cisco
- Latest update: Sep 14,2025
An engineer is implementing OTV on a transport that supports multicast.
The solution needs to meet the following requirements:
• Establish adjacency to the remote peer by using multicast.
• Enable OTV advertisements for VLAN 100 to the other site.
Which two commands should be configured to meet these requirements? (Choose two.)
- A . otv site-vlan 100
- B . otv data-group 232.2.2.0/28
- C . otv use-adjacency-server 172.27.255.94
- D . otv extend-vlan 100
- E . otv control-group 232.1.1.1
An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image.
What is expected to occur in this case?
- A . The system defaults to the backup image version
- B . The system defaults to and boots into the GOLD firmware image
- C . The system defaults to the GOLD firmware image
- D . The system defaults to and boots into the kickstart image
Which configuration statically assigns VSAN membership to a virtual Fibre Channel interface?
- A . switch(config-vsan-cb># vsan 100 bind interface fc 3/1
- B . switch<config-vsan-db)# vsan 100 bind interface vfc 31
- C . switch(config-vsan-db># vsan 100 fc 3/1
- D . switch(config-vsan-db)# vsan 100 interface vfc 31
An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth 1/2 interface for both switches must be advertised via OSPF. However, these interfaces must not establish OSPF adjacency or send routing updates. The current OSPF adjacency over the interface Eth1/1 on SW1 and Eth1/1 on SW2 must remain unaffected.
Which configuration must be applied to both Nexus switches to meet these requirements?
- A . interface ethernet 1/2
passive-interface default - B . Interface ethernet 1/2
Ip ospf network point-to-point - C . interface ethernet 1/2
ip ospf passive-interface - D . interface ethernet 1/2
no ip ospf passive-Interface
DRAG DROP
A network engineer is asked to describe the cloud infrastructure models from the perspective of their operation and access to resources.
Drag and drop the descriptions from the left onto the appropriate.
An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect.
Which backup type must be selected to meet these requirements?
- A . all configuration
- B . system configuration
- C . logical configuration
- D . full state
An engineer must configure HTTPS secure management for Cisco UCS Manager using a key ring named kr2016 and a key size of 1024 bits. The environment consists of a primary fabric interconnect named UCS-A and a secondary fabric interconnect named UCS-B.
Which command sequence must be used to accomplish this goal?
- A . Option A
- B . Option B
- C . Option C
- D . Option D
Which server policy is used to install new Cisco IMC software on a server?
- A . host firmware policy
- B . hypervisor firmware policy
- C . BIOS software policy
- D . Cisco IMC software policy
A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between the Cisco Nexus switch and the backup server is UDP. The backup must be used when the current working configuration of the switch gets corrupted.
Which set of steps must be taken to meet these requirements?
- A . 1 Perform a startup-config backup to an FTP server.
2 Copy startup-config in the boot flash to the running-config file - B . 1 Perform a running-config backup to an SFTP server
2 Copy backup-config from the SFTP server to the running-config file - C . 1 Perform a running-config backup to an SCP server
2 Copy running-config in the boot flash to the running-config file - D . 1 Perform a startup-config backup to a TFTP server
2 Copy backup-config from the backup server to the running-config file
Refer to the exhibit.
An engineer is configuring a VSAN on the network.
Which option must be selected to create the VSAN?
- A . Fabric B
- B . FC Zoning Enabled
- C . Fabric A
- D . Common/Global
Latest 350-601 Dumps Valid Version with 138 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
